UPD78F0552MA-FAA-AX Renesas Electronics America, UPD78F0552MA-FAA-AX Datasheet - Page 429

• Manufacturer Part Number: UPD78F0552MA-FAA-AX
• Description: MCU 8BIT 16-SSOP
• Manufacturer: Renesas Electronics America
• Series: 78K0/Kx2-Lr

Specifications of UPD78F0552MA-FAA-AX

• Core Processor: 78K/0
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: I²C, LIN, UART/USART
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 9
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

<R>
<R>
78K0/Kx2-L
(g) 78K0/KC2-L (44-pin and 48-pin products)
(7) Port mode registers 1, 2, 7 (PM1, PM2, PM7)
R01UH0028EJ0400 Rev.4.00
Sep 27, 2010
Cautions 1. Set the pin set to analog I/O to the input mode by using port mode registers 1, 2, 7 (PM1, PM2,
When using the ANI8/AMP1-/P10 to ANI10/AMP1+/P12, ANI0/AMP0-/P20 to ANI7/P27, and ANI8/P70 to ANI10/P72
pins for analog input port, set PM10 to PM12, PM20 to PM27, PM70 to PM72 to 1. The output latches of P10 to P12,
P20 to P27, and P70 to P72 at this time may be 0 or 1.
If PM10 to PM12, PM20 to PM27, and P70 to P72 are set to 0, they cannot be used as analog input port pins.
PM1, PM2, and PM7 can be set by a 1-bit or 8-bit memory manipulation instruction.
Reset signal generation sets this register to FFH.
Remark A/D converter analog input pins differ depending on products.
Address: FF2EH
Address: FF2FH
Symbol
ADPC0
Symbol
ADPC1
• 78K0/KY2-L:
• 78K0/KA2-L (20-pin products):
• 78K0/KA2-L (25-pin products):
• 78K0/KA2-L (32-pin products):
• 78K0/KB2-L:
• 78K0/KC2-L (40-pin product):
• 78K0/KC2-L (44-pin and 48-pin products):
2. If data is written to ADPC0 and ADPC1, a wait cycle is generated. Do not write data to ADPC0 and
Figure 12-9. Format of A/D Port Configuration Registers 0, 1 (ADPC0, ADPC1) (3/3)
PM7).
ADPC1 when the peripheral hardware clock is stopped.
CAUTIONS FOR WAIT.
ADPCS7
ADPCSn
7
7
0
0
1
After reset: 07H
After reset: 00H
Analog I/O
Digital I/O
ADPCS6
6
6
0
R/W
R/W
ADPCS5
5
5
0
Digital I/O or analog I/O selection (n = 0 to 10)
ADPCS4
ANI0 to ANI3
ANI0 to ANI5
ANI0 to ANI6
ANI0 to ANI10
ANI0 to ANI3, ANI8 to ANI10
ANI0 to ANI6, ANI8 to ANI10
ANI0 to ANI10
4
4
0
ADPCS3
3
3
0
ADPCS10
ADPCS2
CHAPTER 12 A/D CONVERTER
For details, refer to CHAPTER 31
2
2
ADPCS1
ADPCS9
1
1
ADPCS0
ADPCS8
0
0
415