UPD78F0552MA-FAA-AX Renesas Electronics America, UPD78F0552MA-FAA-AX Datasheet - Page 441

• Manufacturer Part Number: UPD78F0552MA-FAA-AX
• Description: MCU 8BIT 16-SSOP
• Manufacturer: Renesas Electronics America
• Series: 78K0/Kx2-Lr

Specifications of UPD78F0552MA-FAA-AX

• Core Processor: 78K/0
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: I²C, LIN, UART/USART
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 9
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

78K0/Kx2-L
R01UH0028EJ0400 Rev.4.00
Sep 27, 2010
The setting methods are described below.
<Change the channel>
<Complete A/D conversion>
<1> Set the A/D conversion time and the operation mode by using bits 5 to 1 (FR2 to FR0, LV1, and LV0) of the
<2> Set bit 0 (ADCE) of ADM0 to 1.
<3> Set the channel to be used to analog input by using the A/D port configuration registers 0, 1 (ADPC0,
<4> Set the PGA operation to set the PGA output or the single AMP operation to set the operational amplifier
<5> Select a channel to be used by using the analog input channel specification register (ADS).
<6> Set bit 7 (ADCS) of ADM0 to 1 to start A/D conversion.
<7> When one A/D conversion has been completed, an interrupt request signal (INTAD) is generated.
<8> Transfer the A/D conversion data to the A/D conversion result register (ADCR, ADCRH, ADCRL).
<9> Set bit 0 (ADMK) of the interrupt mask flag register 1L (MK1L) to 1
<10> Change the channel by using ADS to start A/D conversion.
<11> Clear bit 0 (ADIF) of the interrupt request flag register 1L (IF1L) to 0.
<12> Clear ADMK to 0
<13> When one A/D conversion has been completed, an interrupt request signal (INTAD) is generated.
<14> Transfer the A/D conversion data to the A/D conversion result register (ADCR, ADCRH, ADCRL).
<15> Clear ADCS to 0.
<16> Clear ADCE to 0.
Note Execute this only if interrupt servicing is used for A/D conversion.
Cautions 1. Make sure the period of <2> to <6> is 1
A/D converter mode register 0 (ADM0).
ADPC1) and port mode registers 1, 2 (PM1, PM2).
output for analog input. (refer to CHAPTER 13 OPERATIONAL AMPLIFIERS).
2. If the timing of <2> is earlier than that of <4>, <2> may be performed any time.
3. <2> can be omitted. However, ignore data of the first conversion after <6> in this case.
4. The period from <7> to <13> differs from the conversion time set using bits 5 to 1 (FR2 to
FR0, LV1, LV0) of ADM0. The period from <10> to <13> is the conversion time set using FR2
to FR0, LV1, and LV0.
Note
.
μ
s or more.
Note
.
CHAPTER 12 A/D CONVERTER
427