SAK-TC1766-192F80HL BD Infineon Technologies, SAK-TC1766-192F80HL BD Datasheet - Page 69

• Manufacturer Part Number: SAK-TC1766-192F80HL BD
• Description: IC MCU 32BIT FLASH PG-LQFP-176
• Manufacturer: Infineon Technologies
• Series: TC17xxr

Specifications of SAK-TC1766-192F80HL BD

• Core Processor: TriCore
• Core Size: 32-Bit
• Speed: 80MHz
• Connectivity: ASC, CAN, MLI, MSC, SSC
• Peripherals: DMA, POR, WDT
• Number Of I /o: 81
• Program Memory Size: 1.5MB (1.5M x 8)
• Program Memory Type: FLASH
• Ram Size: 108K x 8
• Voltage - Supply (vcc/vdd): 1.42 V ~ 1.58 V
• Data Converters: A/D 2x10b; A/D 32x8b,10b,12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 176-LFQFP
• Packages: PG-LQFP-176
• Max Clock Frequency: 80.0 MHz
• Sram (incl. Cache): 108.0 KByte
• Can Nodes: 2
• A / D Input Lines (incl. Fadc): 36
• Program Memory: 1.5 MB
• For Use With: B158-H8539-G2-X-7600IN - KIT STARTER TC176X SERIES
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: KT1766192F80HLBDXT; SAK-TC1766-192F80HLBDINTR

Preliminary
Oscillation measurement with the final target system is strongly recommended to verify
the input amplitude at XTAL1 and to determine the actual oscillation allowance (margin
negative resistance) for the oscillator-crystal system.
When using an external clock signal, the signal must be connected to XTAL1. XTAL2 is
left open (unconnected). The external clock frequency can be in the range of 0 - 40 MHz
if the PLL is bypassed, and 4 - 40 MHz if the PLL is used.
The oscillator can also be used in combination with a ceramic resonator. The final
circuitry must also be verified by the resonator vendor.
Figure 3-16
modes, external crystal mode and external input clock mode. A block capacitor is
recommended to be placed between
Figure 3-16 Oscillator Circuitries
Note: For crystal operation, it is strongly recommended to measure the negative
Data Sheet
4 - 25
Fundamental
Mode Crystal
Crystal Frequency
4 MHz
8 MHz
12 MHz
16 - 25 MHz
1) Note that these are evaluation start values!
MHz
resistance in the final target system (layout) to determine the optimum parameters
for the oscillator operation. Please refer to the minimum and maximum values of
the negative resistance specified by the crystal supplier.
C
X1
R
Q
shows the recommended external oscillator circuitries for both operating
C
R
X2
X2
V
XTAL1
XTAL2
DDOSC
C
33 pF
18 pF
12 pF
10 pF
Oscillator
X1
TC1766
V
,
C
SSOSC
X2
V
1)
DDOSC3
R
0
0
0
0
X2
f
1)
OSC
V
DDOSC
65
/
V
DDOSC3
External Clock
Signal
and
4 - 40
MHz
V
SSOSC
Functional Description
V
XTAL1
XTAL2
DDOSC
.
Oscillator
TC1766
V
SSOSC
V
DDOSC3
V1.0, 2008-04
MCS06084
TC1766
f
OSC