QB-MINI2-EE NEC, QB-MINI2-EE Datasheet - Page 38
QB-MINI2-EE
Manufacturer Part Number
QB-MINI2-EE
Description
EMULATOR, PROGRAMMER, MINICUBE2
Manufacturer
NEC
Type
Debug Emulatorr
Datasheet
1.QB-MINI2-EE.pdf
(169 pages)
Specifications of QB-MINI2-EE
Svhc
No SVHC (18-Jun-2010)
Mcu Supported Families
MINICUBE2
Silicon Family Name
V850, 78K0R, 78K0S
Ic Product Type
On-Chip Debug Emulator
Kit Contents
MINICUBE2, USB Cable, Target Cable, 78K0-OCD Board
Features
On-Chip Debugging, Flash Memory Programming,
- Current page: 38 of 169
- Download datasheet (6Mb)
3.2.6 Cautions on debugging
38
(1) Handling of device that was used for debugging
(2) When breaks cannot be executed
(3) When pseudo real-time RAM monitor (RRM) function and DMM function do not operate
(4) Standby release with pseudo RRM and DMM functions enabled
(5) Writing to peripheral I/O registers that requires a specific sequence, using DMM function
This section describes cautions on performing on-chip debugging for a V850 microcontroller.
Be sure to read the following to use MINICUBE2 properly.
Do not mount a device that was used for debugging on a mass-produced product, because the flash memory
was rewritten during debugging and the number of rewrites of the flash memory cannot be guaranteed.
Moreover, do not embed the debug monitor program into mass-produced products.
Forced breaks cannot be executed if one of the following conditions is satisfied.
• Interrupts are disabled (DI)
• Interrupts issued for the serial interface, which is used for communication between MINICUBE2 and the
• Standby mode is entered while standby release by a maskable interrupt is prohibited
• Mode for communication between MINICUBE2 and the target device is UART, and the main clock has been
The pseudo RRM function and DMM function do not operate if one of the following conditions is satisfied.
• Interrupts are disabled (DI)
• Interrupts issued for the serial interface, which is used for communication between MINICUBE2 and the
• Standby mode is entered while standby release by a maskable interrupt is prohibited
• Mode for communication between MINICUBE2 and the target device is UART, and the main clock has been
• Mode for communication between MINICUBE2 and the target device is UART, and a clock different from the
The standby mode is released by the pseudo RRM function and DMM function if one of the following
conditions is satisfied.
• Mode for communication between MINICUBE2 and the target device is CSI-H/S
• Mode for communication between MINICUBE2 and the target device is UART, and the main clock has been
Peripheral I/O registers that requires a specific sequence cannot be written with the DMM function.
target device, are masked
stopped
target device, are masked
stopped
one specified in the debugger is used for communication
supplied
CHAPTER 3
HOW TO USE MINICUBE2 WITH V850 MICROCONTROLLER
User’s Manual U18371EJ1V0UM
Related parts for QB-MINI2-EE
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
16/8 bit single-chip microcomputer
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual audio power amp circuit
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual comparator
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
MOS type composite field effect transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
50 V/100 mA FET array incorporating 2 N-ch MOSFETs
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Twin transistors equipped with different model chips(6P small MM)
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Bipolar analog integrated circuit
Manufacturer:
NEC
Datasheet: