MCF5282CVM66 Freescale, MCF5282CVM66 Datasheet - Page 563

• Manufacturer Part Number: MCF5282CVM66
• Manufacturer: Freescale

Specifications of MCF5282CVM66

• Cpu Family: MCF528x
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 66MHz
• Interface Type: CAN/I2C/QSPI/UART
• Total Internal Ram Size: 64KB
• # I/os (max): 150
• Number Of Timers - General Purpose: 12
• Operating Supply Voltage (typ): 3.3V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 256
• Package Type: MA-BGA
• Program Memory Type: Flash
• Program Memory Size: 512KB
• Lead Free Status / RoHS Status: Compliant

Freescale Semiconductor
15–10
Bit(s)
Address
7–6
5–0
9
8
Reset
R/W:
Field
IST1
CHAN
Name
7
BYP
IST
—
P
Figure 28-14. Conversion Command Word Table (CCW)
IST0
6
Reserved, should be cleared.
Pause. Allows subqueues to be created within queue 1 and queue 2. The QADC
performs the conversion specified by the CCW with the pause bit set and then the
queue enters the pause state. Another trigger event causes execution to continue from
the pause to the next CCW.
1 Enter pause state after execution of current CCW.
0 Do not enter pause state after execution of current CCW.
NOTE: The P bit does not cause the queue to pause in software-initiated modes or
externally gated modes.
Sample amplifier bypass. Enables the amplifier bypass mode for a conversion and
subsequently changes the timing. The initial sample time is eliminated, reducing the
potential conversion time by two QCLKs. However, due to internal RC effects, a
minimum final sample time of four QCLKs must be allowed. When using this mode,
the external circuit should be of low source impedance. Loading effects of the external
circuitry need to be considered because the benefits of the sample amplifier are not
present.
1 Amplifier bypass mode enabled
0 Amplifier bypass mode disabled
NOTE: BYP is maintained for software compatibility but has no functional benefit on
this version of the QADC.
Input sample time. Specifies the length of the sample window. The input sample time
can be varied, under software control, to accommodate various input channel source
impedances. Longer sample times permit more accurate A/D conversions of signals
with higher source impedances.
Table 28-15
The programmable sample time can also be used to adjust queue execution time or
sampling rate by increasing the time interval between conversions.
Selects the input channel number. The CCW channel field is programmed with the
channel number corresponding to the analog input signal to be sampled and
converted. The analog input signal channel number assignments and the signal
definitions vary depending on whether the QADC multiplexed or non-multiplexed
mode is used by the application. As far as queue scanning operations are concerned,
there is no distinction between an internally or externally multiplexed analog input.
Table 28-16
Table 28-17
Programming the channel field to channel 63 denotes the end of the queue. Channels
60 to 62 are special internal channels. When one of the special channels is selected,
the sampling amplifier is not used. The value of V
directly. Programming any input sample time other than two has no benefit for the
special internal channels except to lengthen the overall conversion time.
Table 28-14. CCW Field Descriptions
CHAN5
5
shows the four selectable input sample times.
shows the channel number assignments for non-multiplexed mode.
shows the channel number assignments for multiplexed mode.
IPSBAR + 0x19_0200, 0x19_027e
CHAN4
4
Undefined
R
CHAN3
Description
3
CHAN2
RL
Queued Analog-to-Digital Converter (QADC)
, V
2
RH
, or (V
CHAN1
RH
1
–V
RL
)/2 is converted
CHAN0
0
28-25