C8051F411-GMR Silicon Laboratories Inc, C8051F411-GMR Datasheet - Page 54

• Manufacturer Part Number: C8051F411-GMR
• Description: Microcontrollers (MCU) 50 MIPS 32KB 12ADC RTCLOCK 28 PIN MCU
• Manufacturer: Silicon Laboratories Inc

Specifications of C8051F411-GMR

• Processor Series: C8051F4x
• Core: 8051
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 32 KB
• Data Ram Size: 2.25 KB
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 20
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: QFN
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F410DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 20 Channel
• On-chip Dac: 12 bit, 2 Channel
• Package: 28QFN EP
• Device Core: 8051
• Family Name: C8051F41x
• Maximum Speed: 50 MHz
• Ram Size: 2.25 KB
• Operating Supply Voltage: 1.8|2.5|3.3|5 V
• Operating Temperature: -40 to 85 °C
• Lead Free Status / Rohs Status: Details

C8051F410/1/2/3
Depending on the output connected to the ADC input, additional tracking time, more than is specified in
Table 5.3 and Table 5.4, may be required after changing MUX settings. See the settling time requirements
described in
5.3.3. Timing
ADC0 has a maximum conversion speed specified in Table 5.3 and Table 5.4. ADC0 is clocked from the
ADC0 Subsystem Clock (FCLK). The source of FCLK is selected based on the BURSTEN bit. When
BURSTEN is logic 0, FCLK is derived from the current system clock. When BURSTEN is logic 1, FCLK is
derived from the Burst Mode Oscillator, an independent clock source with a maximum frequency of
25 MHz.
When ADC0 is performing a conversion, it requires a clock source that is typically slower than FCLK. The
ADC0 SAR conversion clock (SAR clock) is a divided version of FCLK. The divide ratio can be configured
using the AD0SC bits in the ADC0CF register. The maximum SAR clock frequency is listed in Table 5.3
and Table 5.4.
ADC0 can be in one of three states at any given time: tracking, converting, or idle. Tracking time depends
on the tracking mode selected. For Pre-Tracking Mode, tracking is managed by software and ADC0 starts
conversions immediately following the convert start signal. For Post-Tracking and Dual-Tracking Modes,
the tracking time after the convert start signal is equal to the value determined by the AD0TK bits plus 2
FCLK cycles. Tracking is immediately followed by a conversion. The ADC0 conversion time is always 13
SAR clock cycles plus an additional 2 FCLK cycles to start and complete a conversion. Figure 5.4 shows
timing diagrams for a conversion in Pre-Tracking Mode and tracking plus conversion in Post-Tracking or
Dual-Tracking Mode. In this example, repeat count is set to one.
54
Dual-Tracking
Post-Tracking
Convert Start
Pre-Tracking
AD0TM = 10
AD0TM = 11
AD0TM= 01
Section “5.3.6. Settling Time Requirements” on page 58
Track
Track
Idle
Track
Track
Figure 5.3. ADC0 Tracking Modes
Convert
Rev. 1.1
Convert
Convert
Track
.
Track
Idle
Track
Track
Convert ...
Convert..
Convert..