C8051F411-GMR Silicon Laboratories Inc, C8051F411-GMR Datasheet - Page 63

• Manufacturer Part Number: C8051F411-GMR
• Description: Microcontrollers (MCU) 50 MIPS 32KB 12ADC RTCLOCK 28 PIN MCU
• Manufacturer: Silicon Laboratories Inc

Specifications of C8051F411-GMR

• Processor Series: C8051F4x
• Core: 8051
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 32 KB
• Data Ram Size: 2.25 KB
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 20
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: QFN
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F410DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 20 Channel
• On-chip Dac: 12 bit, 2 Channel
• Package: 28QFN EP
• Device Core: 8051
• Family Name: C8051F41x
• Maximum Speed: 50 MHz
• Ram Size: 2.25 KB
• Operating Supply Voltage: 1.8|2.5|3.3|5 V
• Operating Temperature: -40 to 85 °C
• Lead Free Status / Rohs Status: Details

5.4.
The ADC Programmable Window Detector continuously compares the ADC0 output registers to user-pro-
grammed limits, and notifies the system when a desired condition is detected. This is especially effective in
an interrupt-driven system, saving code space and CPU bandwidth while delivering faster system
response times. The window detector interrupt flag (AD0WINT in register ADC0CN) can also be used in
polled mode. The ADC0 Greater-Than (ADC0GTH, ADC0GTL) and Less-Than (ADC0LTH, ADC0LTL)
registers hold the comparison values. The window detector flag can be programmed to indicate when mea-
sured data is inside or outside of the user-programmed limits, depending on the contents of the ADC0
Less-Than and ADC0 Greater-Than registers.
Bits7–4: AD0PWR3–0: ADC0 Burst Power-Up Time.
Bits3–2: AD0TM1–0: ADC0 Tracking Mode Select Bits.
Bits1–0: AD0TK1–0: ADC0 Post-Track Time.
R/W
Bit7
Programmable Window Detector
For BURSTEN = 0:
ADC0 power state controlled by AD0EN.
For BURSTEN = 1 and AD0EN = 1;
ADC0 remains enabled and does not enter the low power state.
For BURSTEN = 1 and AD0EN = 0:
ADC0 enters the low power state as specified in Table 5.3 and Table 5.4 and is enabled
after each convert start signal. The Power Up time is programmed according to the following
equation:
00: Reserved.
01: ADC0 is configured to Post-Tracking Mode.
10: ADC0 is configured to Pre-Tracking Mode.
11: ADC0 is configured to Dual-Tracking Mode (default).
Post-Tracking time is controlled by AD0TK as follows:
00: Post-Tracking time is equal to 2 SAR clock cycles + 2 FCLK cycles.
01: Post-Tracking time is equal to 4 SAR clock cycles + 2 FCLK cycles.
10: Post-Tracking time is equal to 8 SAR clock cycles + 2 FCLK cycles.
11: Post-Tracking time is equal to 16 SAR clock cycles + 2 FCLK cycles.
AD0PWR
SFR Definition 5.6. ADC0TK: ADC0 Tracking Mode Select
R/W
Bit6
AD0PWR
=
Tstartup
---------------------- 1
R/W
Bit5
400ns
–
R/W
Bit4
or
Tstartup
Rev. 1.1
R/W
Bit3
AD0TM
=
R/W
Bit2

AD0PWR
C8051F410/1/2/3
R/W
Bit1
+
AD0TK
1
(bit addressable)
400ns
R/W
Bit0
SFR Address:
Reset Value
11111111
0xBA
63