SAM7S16 Atmel Corporation, SAM7S16 Datasheet - Page 133

• Manufacturer Part Number: SAM7S16
• Manufacturer: Atmel Corporation

Specifications of SAM7S16

• Flash (kbytes): 16 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 55 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 21
• Ext Interrupts: 21
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 2
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 4
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

20.2.5.5
20.2.5.6
6175L–ATARM–28-Jul-11
Flash General-purpose NVM Commands
Flash Security Bit Command
In the same way, the Clear Lock command (CLB) is used to clear lock bits. All the lock bits are
also cleared by the EA command.
Table 20-11. Set and Clear Lock Bit Command
Lock bits can be read using Get Lock Bit command (GLB). The n
n of the bit mask is set..
Table 20-12. Get Lock Bit Command
General-purpose NVM bits (GP NVM bits) can be set using the Set GPNVM command (SGPB).
This command also activates GP NVM bits. A bit mask is provided as argument to the com-
mand. When bit 0 of the bit mask is set, then the first GP NVM bit is activated.
In the same way, the Clear GPNVM command (CGPB) is used to clear general-purpose NVM
bits. All the general-purpose NVM bits are also cleared by the EA command. The general-pur-
pose NVM bit is deactivated when the corresponding bit in the pattern value is set to 1.
Table 20-13. Set/Clear GP NVM Command
General-purpose NVM bits can be read using the Get GPNVM Bit command (GGPB). The n
GP NVM bit is active when bit n of the bit mask is set..
Table 20-14. Get GP NVM Bit Command
A security bit can be set using the Set Security Bit command (SSE). Once the security bit is
active, the Fast Flash programming is disabled. No other command can be run. An event on the
Erase pin can erase the security bit once the contents of the Flash have been erased.
Step
1
2
Step
1
2
Step
1
2
Step
1
2
Handshake Sequence
Write handshaking
Write handshaking
Handshake Sequence
Write handshaking
Read handshaking
Handshake Sequence
Write handshaking
Write handshaking
Handshake Sequence
Write handshaking
Read handshaking
MODE[3:0]
CMDE
DATA
MODE[3:0]
CMDE
DATA
MODE[3:0]
CMDE
DATA
MODE[3:0]
CMDE
DATA
SLB or CLB
GLB
DATA[15:0] or DATA[7:0]
Bit Mask
DATA[15:0] or DATA[7:0]
Lock Bit Mask Status
0 = Lock bit is cleared
1 = Lock bit is set
DATA[15:0] or DATA[7:0]
SGPB or CGPB
GP NVM bit pattern value
DATA[15:0] or DATA[7:0]
GGPB
GP NVM Bit Mask Status
0 = GP NVM bit is cleared
1 = GP NVM bit is set
th
lock bit is active when the bit
SAM7S Series
133
th