SAM7S16 Atmel Corporation, SAM7S16 Datasheet - Page 446

• Manufacturer Part Number: SAM7S16
• Manufacturer: Atmel Corporation

Specifications of SAM7S16

• Flash (kbytes): 16 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 55 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 21
• Ext Interrupts: 21
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 2
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 4
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

33.5
33.5.1
33.5.2
33.5.3
446
Functional Description
SAM7S Series
TC Description
16-bit Counter
Clock Selection
The three channels of the Timer Counter are independent and identical in operation. The regis-
ters for channel programming are listed in
Each channel is organized around a 16-bit counter. The value of the counter is incremented at
each positive edge of the selected clock. When the counter has reached the value 0xFFFF and
passes to 0x0000, an overflow occurs and the COVFS bit in TC_SR (Status Register) is set.
The current value of the counter is accessible in real time by reading the Counter Value Regis-
ter, TC_CV. The counter can be reset by a trigger. In this case, the counter value passes to
0x0000 on the next valid edge of the selected clock.
At block level, input clock signals of each channel can either be connected to the external inputs
TCLK0, TCLK1 or TCLK2, or be connected to the internal I/O signals TIOA0, TIOA1 or TIOA2
for chaining by programming the TC_BMR (Block Mode). See
Each channel can independently select an internal or external clock source for its counter:
•
•
This selection is made by the TCCLKS bits in the TC Channel Mode Register.
The selected clock can be inverted with the CLKI bit in TC_CMR. This allows counting on the
opposite edges of the clock.
The burst function allows the clock to be validated when an external signal is high. The BURST
parameter in the Mode Register defines this signal (none, XC0, XC1, XC2). See
page 447
Note:
Internal clock signals: TIMER_CLOCK1, TIMER_CLOCK2, TIMER_CLOCK3,
TIMER_CLOCK4, TIMER_CLOCK5
External clock signals: XC0, XC1 or XC2
In all cases, if an external clock is used, the duration of each of its levels must be longer than the
master clock period. The external clock frequency must be at least 2.5 times lower than the mas-
ter clock
Table 33-4 on page
Figure 33-2 on page
459.
6175L–ATARM–28-Jul-11
Figure 33-3 on
447.