SAM7S16 Atmel Corporation, SAM7S16 Datasheet - Page 527

• Manufacturer Part Number: SAM7S16
• Manufacturer: Atmel Corporation

Specifications of SAM7S16

• Flash (kbytes): 16 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 55 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 21
• Ext Interrupts: 21
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 2
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 4
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

35.6.10
Register Name:
Access Type:
WARNING: Due to synchronization between MCK and UDPCK, the software application must wait for the end of the write
operation before executing another write by polling the bits which must be set/cleared.
Note:
• TXCOMP: Generates an IN Packet with Data Previously Written in the DPR
This flag generates an interrupt while it is set to one.
Write (Cleared by the firmware):
0 = Clear the flag, clear the interrupt.
1 = No effect.
Read (Set by the USB peripheral):
0 = Data IN transaction has not been acknowledged by the Host.
1 = Data IN transaction is achieved, acknowledged by the Host.
After having issued a Data IN transaction setting TXPKTRDY, the device firmware waits for TXCOMP to be sure that the
host has acknowledged the transaction.
6175L–ATARM–28-Jul-11
//! Clear flags of UDP UDP_CSR register and waits for synchronization
#define Udp_ep_clr_flag(pInterface, endpoint, flags) { \
//! Set flags of UDP UDP_CSR register and waits for synchronization
#define Udp_ep_set_flag(pInterface, endpoint, flags) { \
EPEDS
DIR
31
23
15
–
7
pInterface->UDP_CSR[endpoint] &= ~(flags); \
while ( (pInterface->UDP_CSR[endpoint] & (flags)) == (flags) ); \
}
pInterface->UDP_CSR[endpoint] |= (flags); \
while ( (pInterface->UDP_CSR[endpoint] & (flags)) != (flags) ); \
}
In a preemptive environment, set or clear the flag and wait for a time of 1 UDPCK clock cycle and 1peripheral clock cycle. How-
ever, RX_DATA_BLK0, TXPKTRDY, RX_DATA_BK1 require wait times of 3 UDPCK clock cycles and 3 peripheral clock cycles
before accessing DPR.
UDP Endpoint Control and Status Register
RX_DATA_
BK1
30
22
14
UDP_ CSRx [x = 0..Y]
Read-write
–
–
6
FORCE
STALL
29
21
13
–
–
5
TXPKTRDY
28
20
12
–
–
4
RXBYTECNT
STALLSENT
ISOERROR
DTGLE
27
19
11
–
3
RXSETUP
26
18
10
2
RXBYTECNT
RX_DATA_
SAM7S Series
EPTYPE
BK0
25
17
9
1
TXCOMP
24
16
8
0
527