SAM7S16 Atmel Corporation, SAM7S16 Datasheet - Page 644
SAM7S16
Manufacturer Part Number
SAM7S16
Description
Manufacturer
Atmel Corporation
Specifications of SAM7S16
Flash (kbytes)
16 Kbytes
Pin Count
48
Max. Operating Frequency
55 MHz
Cpu
ARM7TDMI
Hardware Qtouch Acquisition
No
Max I/o Pins
21
Ext Interrupts
21
Usb Speed
No
Usb Interface
No
Spi
1
Twi (i2c)
1
Uart
2
Ssc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
384
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
4
Self Program Memory
NO
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
3.0 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
3
Input Capture Channels
3
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- Current page: 644 of 781
- Download datasheet (12Mb)
40.9
40.9.1
40.9.1.1
40.9.2
40.9.2.1
40.9.2.2
644
SAM7S256 Errata - Revision C Parts
SAM7S Series
Embedded Flash Controller (EFC)
Parallel Input/Output Controller (PIO)
EFC: Embedded Flash Access Time 1
PIO: Electrical Characteristics on NRST and PA0-PA16 and PA21-31
PIO: Drive Low NRST, PA0-PA16 and PA21-PA31
Refer to
Note: AT91SAM7S256 Revision C chip ID is 0x270B 0942.
The embedded Flash maximum access time is 20 MHz (instead of 30 MHz) at zero Wait State
(FWS = 0).
The maximum operating frequency with one Wait State (FWS = 1) is 48.1 MHz (instead of
55 MHz). Above 48.1 MHz and up to 55 MHz, two Wait States (FWS = 2) are required.
Set the number of Wait States (FWS) according to the frequency requirements described in this
errata.
When NRST or PA0-PA16 or PA21-PA31 are set as digital inputs with pull-up enabled, the volt-
age of the I/O stabilizes at VPull-up.
Vpull-up
This condition causes a leakage through VDDIO. This leakage is 45 µA per pad in worst case at
3.3 V, and 25 µA at 1.8V.
I Leakage
It is recommended to use an external pull-up if needed.
When NRST or PA0-PA16 and or PA21-PA31 are set as digital inputs with pull-up enabled, driv-
ing the I/O with an output impedance higher than 500 ohms may not drive the I/O to a logical
zero.
Output impedance must be lower than 500 ohms.
VPull-up Min
VDDIO - 0.65 V
Parameter
I Leakage at 3,3V
I Leakage at 1.8V
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Section 40.1 “Marking” on page
VPull-up Max
VDDIO - 0.45 V
Typ
2.5
1
µA
µA
Max
45
25
µA
µA
591.
6175L–ATARM–28-Jul-11
Related parts for SAM7S16
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: