ISP1362EE/01 PHILIPS [NXP Semiconductors], ISP1362EE/01 Datasheet - Page 75
![no-image](/images/no-image-200.jpg)
ISP1362EE/01
Manufacturer Part Number
ISP1362EE/01
Description
Single-chip Universal Serial Bus On-The-Go controller
Manufacturer
PHILIPS [NXP Semiconductors]
Datasheet
1.ISP1362EE01.pdf
(150 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISP1362EE/01
Manufacturer:
KAWASAKI
Quantity:
1 200
Part Number:
ISP1362EE/01
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
- Current page: 75 of 150
- Download datasheet (620Kb)
Philips Semiconductors
9397 750 12337
Product data
15.1.5 HcInterruptEnable register (R/W: 04H/84H)
Table 42:
Each enable bit in the HcInterruptEnable register corresponds to an associated
interrupt bit in the HcInterruptStatus register. The HcInterruptEnable register is used
to control which events generate a hardware interrupt. When the following three
conditions occur:
Then, a hardware interrupt is requested on the host bus.
Writing logic 1 to a bit in the HcInterruptEnable register sets the corresponding bit,
whereas writing logic 0 to a bit in this register leaves the corresponding bit
unchanged. On a read, the current value of this register is returned.
the bit allocation of the register.
Code (Hex): 04 — read
Code (Hex): 84 — write
Bit
31 to 7
6
5
4
3
2
1
0
•
•
•
A bit is set in the HcInterruptStatus register
The corresponding bit in the HcInterruptEnable register is set
The MasterInterruptEnable (MIE) bit is set.
HcInterruptStatus register: bit description
Symbol
-
RHSC
FNO
UE
RD
SF
-
SO
Rev. 03 — 06 January 2004
Description
reserved
RootHubStatusChange: This bit is set when the content of
HcRhStatus or the content of any of
HcRhPortStatus[NumberofDownstreamPort] has changed.
FrameNumberOverflow: This bit is set when the MSB of
HcFmNumber (bit 15) changes from logic 0 to 1 or from logic 1
to 0.
UnrecoverableError: This bit is set when the HC detects a
system error not related to the USB. The HC should not proceed
with any processing nor signaling before the system error has
been corrected. The HCD clears this bit after the HC has been
reset.
Philips Host Controller Interface (PHCI): Always set to logic 0.
ResumeDetected: This bit is set when the HC detects that a
device on the USB is asserting resume signaling. It is the transition
from no resume signaling to resume signaling causing this bit to be
set. This bit is not set when the HCD sets the USBResume state.
StartOfFrame: At the start of each frame, this bit is set by the HC
and an SOF is generated.
reserved
SchedulingOverrun: This bit is set when the USB schedules for
current frame overruns. A scheduling overrun also causes the
SchedulingOverrunCount (SOC) of HcCommandStatus to be
incremented.
Single-chip USB OTG controller
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Table 43
ISP1362
contains
75 of 150
Related parts for ISP1362EE/01
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ICM7555IN](/images/no-image3.png)
Part Number:
Description:
General purpose CMOS timer
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC16C554BIB64](/images/no-image3.png)
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![BZW03-C100](/images/no-image3.png)
Part Number:
Description:
Voltage regulator diodes
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![P51XAG30KFA](/images/no-image3.png)
Part Number:
Description:
XA 16-bit microcontroller family 32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC16C2550B_07](/images/no-image3.png)
Part Number:
Description:
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC16C650BIBS](/images/no-image3.png)
Part Number:
Description:
5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC16C652BIBS](/images/no-image3.png)
Part Number:
Description:
5V, 3.3 V and 2.5V dual UART, 5 Mbit/s (max.),with 32-byte FIFOs and infrared(IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC16C654BIB64](/images/no-image3.png)
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.), with 64-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC16IS740IPW](/images/no-image3.png)
Part Number:
Description:
Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC18IM700IPW](/images/no-image3.png)
Part Number:
Description:
Master I-2C - bus controller with UART interface
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![TFA9812HN](/images/no-image3.png)
Part Number:
Description:
BTL stereo Class-D audio amplifier with I2S input
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![TFA9881_1104](/images/no-image3.png)
Part Number:
Description:
3.4 W PDM input class-D audio amplifier
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![PC88](/images/no-image3.png)
Part Number:
Description:
TRIODE FOR USE AS GROUNDED GRID U.H.F. AMPLIFIER
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![TH0912250](/images/manufacturer_photos/0/5/522/philips_semiconductors_tmb.jpg)
Part Number:
Description:
Specific Thales (NXP : BLA0912-250,112)
Manufacturer:
Philips Semiconductors
![TH0912251](/images/manufacturer_photos/0/5/522/philips_semiconductors_tmb.jpg)
Part Number:
Description:
Specific Thales (NXP : MX0912B251Y,114)
Manufacturer:
Philips Semiconductors