ISP1362EE/01 PHILIPS [NXP Semiconductors], ISP1362EE/01 Datasheet - Page 88
![no-image](/images/no-image-200.jpg)
ISP1362EE/01
Manufacturer Part Number
ISP1362EE/01
Description
Single-chip Universal Serial Bus On-The-Go controller
Manufacturer
PHILIPS [NXP Semiconductors]
Datasheet
1.ISP1362EE01.pdf
(150 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISP1362EE/01
Manufacturer:
KAWASAKI
Quantity:
1 200
Part Number:
ISP1362EE/01
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
- Current page: 88 of 150
- Download datasheet (620Kb)
Philips Semiconductors
9397 750 12337
Product data
Table 62:
Bit
31 to 21
20
19
18
17
16
15 to 10
HcRhPortStatus[1:2] register: bit description
Symbol
-
PRSC
OCIC
PSSC
PESC
CSC
-
Rev. 03 — 06 January 2004
Description
reserved
PortResetStatusChange: This bit is set at the end of the 10 ms
port reset signal. The HCD can write logic 1 to clear this bit.
Writing logic 0 has no effect.
0 — port reset is not complete
1 — port reset is complete
PortOverCurrentIndicatorChange: This bit is valid only if
overcurrent conditions are reported on a per-port basis. This bit is
set when the Root Hub changes the PortOverCurrentIndicator
(POCI) bit. The HCD can write logic 1 to clear this bit. Writing
logic 0 has no effect.
0 — no change in PortOverCurrentIndicator (POCI)
1 — PortOverCurrentIndicator (POCI) has changed
PortSuspendStatusChange: This bit is set when the full resume
sequence is complete. This sequence includes the 20 ms resume
pulse, LS EOP and 3 ms re-synchronization delay. The HCD can
write logic 1 to clear this bit. Writing logic 0 has no effect. This bit is
also cleared when ResetStatusChange is set.
0 — resume is not completed
1 — resume is completed
PortEnableStatusChange: This bit is set when hardware events
cause the PortEnableStatus (PES) bit to be cleared. Changes from
the HCD writes do not set this bit. The HCD can write logic 1 to
clear this bit. Writing logic 0 has no effect.
0 — no change in PortEnableStatus (PES)
1 — change in PortEnableStatus (PES)
ConnectStatusChange: This bit is set whenever a connect or
disconnect event occurs. The HCD can write logic 1 to clear this
bit. Writing logic 0 has no effect. If CurrentConnectStatus (CCS) is
cleared when a SetPortReset, SetPortEnable or SetPortSuspend
write occurs, this bit is set to force the driver to re-evaluate the
connection status because these writes should not occur if the port
is disconnected.
0 — no change in CurrentConnectStatus (CCS)
1 — change in CurrentConnectStatus (CCS)
Remark: If the DeviceRemovable[NDP] bit is set, this bit is set only
after a Root Hub reset to inform the system that the device is
attached.
reserved
Single-chip USB OTG controller
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
ISP1362
88 of 150
Related parts for ISP1362EE/01
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ICM7555IN](/images/no-image3.png)
Part Number:
Description:
General purpose CMOS timer
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC16C554BIB64](/images/no-image3.png)
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![BZW03-C100](/images/no-image3.png)
Part Number:
Description:
Voltage regulator diodes
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![P51XAG30KFA](/images/no-image3.png)
Part Number:
Description:
XA 16-bit microcontroller family 32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC16C2550B_07](/images/no-image3.png)
Part Number:
Description:
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC16C650BIBS](/images/no-image3.png)
Part Number:
Description:
5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC16C652BIBS](/images/no-image3.png)
Part Number:
Description:
5V, 3.3 V and 2.5V dual UART, 5 Mbit/s (max.),with 32-byte FIFOs and infrared(IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC16C654BIB64](/images/no-image3.png)
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.), with 64-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC16IS740IPW](/images/no-image3.png)
Part Number:
Description:
Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC18IM700IPW](/images/no-image3.png)
Part Number:
Description:
Master I-2C - bus controller with UART interface
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![TFA9812HN](/images/no-image3.png)
Part Number:
Description:
BTL stereo Class-D audio amplifier with I2S input
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![TFA9881_1104](/images/no-image3.png)
Part Number:
Description:
3.4 W PDM input class-D audio amplifier
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![PC88](/images/no-image3.png)
Part Number:
Description:
TRIODE FOR USE AS GROUNDED GRID U.H.F. AMPLIFIER
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![TH0912250](/images/manufacturer_photos/0/5/522/philips_semiconductors_tmb.jpg)
Part Number:
Description:
Specific Thales (NXP : BLA0912-250,112)
Manufacturer:
Philips Semiconductors
![TH0912251](/images/manufacturer_photos/0/5/522/philips_semiconductors_tmb.jpg)
Part Number:
Description:
Specific Thales (NXP : MX0912B251Y,114)
Manufacturer:
Philips Semiconductors