MT48LC4M32B2P-6:G Micron Technology Inc, MT48LC4M32B2P-6:G Datasheet - Page 22

• Manufacturer Part Number: MT48LC4M32B2P-6:G
• Description: IC SDRAM 128MBIT 167MHZ 86TSOP
• Manufacturer: Micron Technology Inc
• Type: SDRAMr

Specifications of MT48LC4M32B2P-6:G

• Package / Case: 86-TSOPII
• Format - Memory: RAM
• Memory Type: SDRAM
• Memory Size: 128M (4Mx32)
• Speed: 167MHz
• Interface: Parallel
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: 0°C ~ 70°C
• Access Time: RoHS Compliant
• Memory Case Style: TSOP
• No. Of Pins: 86
• Operating Temperature Range: 0°C To +70°C
• Operating Temperature Max: 70°C
• Operating Temperature Min: 0°C
• Organization: 4Mx32
• Density: 128Mb
• Address Bus: 14b
• Access Time (max): 17/7.5/5.5ns
• Maximum Clock Rate: 166MHz
• Operating Supply Voltage (typ): 3.3V
• Package Type: TSOP-II
• Operating Temp Range: 0C to 70C
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Supply Current: 195mA
• Pin Count: 86
• Mounting: Surface Mount
• Operating Temperature Classification: Commercial
• Memory Configuration: 4 BLK (1M X 32)
• Interface Type: LVTTL
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Figure 9:
PDF: 09005aef80872800/Source: 09005aef80863355
128MbSDRAMx32_2.fm - Rev. L 1/09 EN
CAS Latency
Upon completion of a burst, assuming no other commands have been initiated, the DQs
will go High-Z. A full-page burst will continue until terminated. (At the end of the page, it
will wrap to column 0 and continue.)
Data from any READ burst may be truncated with a subsequent READ command, and
data from a fixed-length READ burst may be immediately followed by data from a READ
command. In either case, a continuous flow of data can be maintained. The first data
element from the new burst follows either the last element of a completed burst or the
last desired data element of a longer burst that is being truncated. The new READ
command should be issued x cycles before the clock edge at which the last desired data
element is valid, where x = CL - 1. This is shown in Figure 10 on page 23 for CAS latencies
of one, two and three; data element n + 3 is either the last of a burst of four or the last
desired of a longer burst. This 128Mb SDRAM uses a pipelined architecture and there-
fore does not require the 2n rule associated with a prefetch architecture.
COMMAND
COMMAND
COMMAND
A READ command can be initiated on any clock cycle following a previous READ
command. Full-speed random read accesses can be performed to the same bank, as
shown in Figure 11 on page 24, or each subsequent READ may be performed to a
different bank.
CLK
CLK
CLK
DQ
DQ
DQ
READ
READ
READ
T0
T0
T0
t
t AC
LZ
CL = 1
CL = 2
NOP
NOP
T1
NOP
T1
T1
t
t AC
LZ
D
t OH
OUT
CL = 3
22
T2
NOP
T2
NOP
T2
t
t AC
LZ
D
t OH
OUT
Micron Technology, Inc., reserves the right to change products or specifications without notice.
T3
T3
NOP
D
t OH
OUT
DON’T CARE
UNDEFINED
T4
©2001 Micron Technology, Inc. All rights reserved.
128Mb: x32 SDRAM
Register Definition