MD5811-D256-V3Q18-P SanDisk, MD5811-D256-V3Q18-P Datasheet - Page 15

no-image

MD5811-D256-V3Q18-P

Manufacturer Part Number
MD5811-D256-V3Q18-P
Description
IC MDOC P3 256MB 48-TSOP
Manufacturer
SanDisk
Datasheet

Specifications of MD5811-D256-V3Q18-P

Format - Memory
FLASH
Memory Type
FLASH - Nand
Memory Size
256M (32M x 8)
Speed
55ns
Interface
Parallel
Voltage - Supply
2.5 V ~ 3.6 V
Operating Temperature
0°C ~ 70°C
Package / Case
48-TSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MD5811-D256-V3Q18-P
Manufacturer:
M-SYSTEMS
Quantity:
20 000
Part Number:
MD5811-D256-V3Q18-P/Y
Manufacturer:
PULSE
Quantity:
47
Part Number:
MD5811-D256-V3Q18-P/Y
Manufacturer:
M-SYSTEMS
Quantity:
20 000
7x10 FBGA Package
12
A[12:11]
A[10:8]
A[7:4]
A[3:0]
D[15:14]
D[13:12]
D[11:8]
D[7:6]
D[5:3]
D[2:0]
CE#
OE#
WE#
ID[1:0]
LOCK#
IF_CFG
BUSY#
RSTIN#
CLK
DMARQ#
Table 2: Signal Descriptions for Standard Interface (Mobile DiskOnChip P3 256Mb 7x10 FBGA Package)
Signal
C2, D2, E2, F2
D1, E1, F1, G1
K4, J3, H3, K2
K6, H5, H4
F6, E6, C6
K3, G3, J2
Ball No.
D7, C7
H7, K7
G8, F7
H6, J6
J7, G6
H1
H2
C5
E7
D4
K5
G7
F3
E4
ST, R8 Data bus, high byte. Not used and may be left
Input
Type
OD
OD
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
Address bus. A0 is multiplexed with the DPD ball.
floating when IF_CFG is set to 0 (8-bit mode).
Data bus, low byte.
Chip Enable, active low
Write Enable, active low
Output Enable, active low
Identification. Configuration control to support up to
four chips cascaded in the same memory window.
Chip 1 = ID1, ID0 = VSS, VSS (0,0); must be used
Chip 2 = ID1, ID0 = VSS, VCCQ (0,1)
Chip 3 = ID1, ID0 = VCCQ, VSS (1,0)
Chip 4 = ID1, ID0 = VCCQ, VCCQ (1,1)
Lock, active low. When active, provides full
hardware data protection of selected partitions.
Interface Configuration, 1 (VCCQ) for 16-bit
interface mode, 0 (VSS) for 8-bit interface mode.
Busy, active low, open drain. Indicates that
DiskOnChip is initializing and should not be
accessed. A 10 KΩ pull-up resistor is required if
this ball drives an input. A 10 KΩ pull-up resistor is
recommended even if this ball is not used.
Reset, active low.
System Clock.
DMA Request, active low. A 10 KΩ pull-up resistor
is required if this ball drives an input. A 10 KΩ pull-
up resistor is recommended even if this ball is not
used.
Data Sheet, Rev. 0.3
System Interface
Configuration
Control
Description
for single chip configuration
Mobile DiskOnChip P3
93-SR-009-8L
Signal
Output
Output
Output
Output
Input/
Input/
Type
Input
Input
Input
Input
Input
Input
Input
Input
Input

Related parts for MD5811-D256-V3Q18-P