MA180023 Microchip Technology, MA180023 Datasheet - Page 179

• Manufacturer Part Number: MA180023
• Description: MODULE PLUG-IN PIC18F46J11 PIM
• Manufacturer: Microchip Technology
• Series: PIC®r

Specifications of MA180023

• Accessory Type: Plug-In Module (PIM) - PIC18F46J11
• Tool / Board Applications: General Purpose MCU, MPU, DSP, DSC
• Mcu Supported Families: PIC18
• Supported Devices: Stand-alone Or W/ HPC(DM183022) Or PIC18(DM183032)
• Silicon Manufacturer: Microchip
• Core Architecture: PIC
• Core Sub-architecture: PIC18
• Silicon Core Number: PIC18F
• Silicon Family Name: PIC18FxxJxx
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: HPC Explorer Board (DM183022) or PIC18 Explorer Board (DM183032)
• For Use With: DM183032 - BOARD EXPLORER PICDEM PIC18DM183022 - BOARD DEMO PIC18FXX22 64/80TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

10.3
In its Master modes, the PMP module provides an 8-bit
data bus, up to 16 bits of address, and all the necessary
control signals to operate a variety of external parallel
devices, such as memory devices, peripherals and
slave microcontrollers. To use the PMP as a master,
the module must be enabled (PMPEN = 1) and the
mode must be set to one of the two possible Master
modes (PMMODEH<1:0> = 10 or 11).
Because there are a number of parallel devices with a
variety of control methods, the PMP module is designed
to be extremely flexible to accommodate a range of
configurations. Some of these features include:
• 8-Bit and 16-Bit Data modes on an 8-bit data bus
• Configurable address/data multiplexing
• Up to two chip select lines
• Up to 16 selectable address lines
• Address auto-increment and auto-decrement
• Selectable polarity on all control lines
• Configurable Wait states at different stages of the
10.3.1
Multiple control bits are used to configure the presence
or absence of control and address signals in the
module. These bits are PTBEEN, PTWREN, PTRDEN
and PTEN<15:0>. They give the user the ability to con-
serve pins for other functions and allow flexibility to
control the external address. When any one of these
bits is set, the associated function is present on its
associated pin; when clear, the associated pin reverts
to its defined I/O port function.
Setting a PTENx bit will enable the associated pin as
an address pin and drive the corresponding data
contained in the PMADDR register. Clearing a PTENx
bit will force the pin to revert to its original I/O function.
For the pins configured as chip select (PMCS1 or
PMCS2) with the corresponding PTENx bit set, the
PTEN0 and PTEN1 bits will also control the PMALL
and PMALH signals. When multiplexing is used, the
associated address latch signals should be enabled.
10.3.2
The PMP module supports two distinct read/write
signaling methods. In Master Mode 1, read and write
strobes are combined into a single control line,
PMRD/PMWR. A second control line, PMENB, deter-
mines when a read or write action is to be taken. In
Master Mode 2, separate read and write strobes
(PMRD and PMWR) are supplied on separate pins.
All control signals (PMRD, PMWR, PMBE, PMENB,
PMAL and PMCSx) can be individually configured as
either positive or negative polarity. Configuration is
controlled by separate bits in the PMCONL register.
© 2009 Microchip Technology Inc.
read/write cycle
MASTER PORT MODES
PMP AND I/O PIN CONTROL
READ/WRITE CONTROL
PIC18F46J11 FAMILY
Note that the polarity of control signals that share the
same output pin (for example, PMWR and PMENB) are
controlled by the same bit; the configuration depends
on which Master Port mode is being used.
10.3.3
The PMP supports data widths of both 8 bits and
16 bits. The data width is selected by the MODE16 bit
(PMMODEH<2>). Because the data path into and out
of the module is only 8 bits wide, 16-bit operations are
always handled in a multiplexed fashion, with the Least
Significant Byte (LSB) of data being presented first. To
differentiate data bytes, the byte enable control strobe,
PMBE, is used to signal when the Most Significant Byte
(MSB) of data is being presented on the data lines.
10.3.4
In either of the Master modes (PMMODEH<1:0> = 1x),
the user can configure the address bus to be multiplexed
together with the data bus. This is accomplished by
using the ADRMUX<1:0> bits (PMCONH<4:3>). There
are three address multiplexing modes available; typical
pinout configurations for these modes are displayed in
Figure 10-9, Figure 10-10 and Figure 10-11.
In Demultiplexed mode (PMCONH<4:3> = 00), data and
address information are completely separated. Data bits
are presented on PMD<7:0> and address bits are
presented on PMADDRH<6:0> and PMADDRL<7:0>.
In Partially Multiplexed mode (PMCONH<4:3> = 01), the
lower eight bits of the address are multiplexed with the
data pins on PMD<7:0>. The upper eight bits of address
are unaffected and are presented on PMADDRH<6:0>.
The PMA0 pin is used as an address latch, and presents
the address latch low enable strobe (PMALL). The read
and write sequences are extended by a complete CPU
cycle during which the address is presented on the
PMD<7:0> pins.
In Fully Multiplexed mode (PMCONH<4:3> = 10), the
entire 16 bits of the address are multiplexed with the
data pins on PMD<7:0>. The PMA0 and PMA1 pins are
used to present address latch low enable (PMALL) and
address
respectively. The read and write sequences are
extended by two complete CPU cycles. During the first
cycle, the lower eight bits of the address are presented
on the PMD<7:0> pins with the PMALL strobe active.
During the second cycle, the upper eight bits of the
address are presented on the PMD<7:0> pins with the
PMALH strobe active. In the event the upper address
bits are configured
corresponding address bits are automatically forced
to ‘0’.
latch
DATA WIDTH
ADDRESS MULTIPLEXING
high
as chip select
enable
(PMALH)
DS39932C-page 179
pins,
strobes,
the