MC68HC705C8ACFNE Freescale Semiconductor, MC68HC705C8ACFNE Datasheet - Page 73

• Manufacturer Part Number: MC68HC705C8ACFNE
• Description: IC MCU 8K 2.1MHZ OTP 44-PLCC
• Manufacturer: Freescale Semiconductor
• Series: HC05r

Specifications of MC68HC705C8ACFNE

• Core Processor: HC05
• Core Size: 8-Bit
• Speed: 2.1MHz
• Connectivity: SCI, SPI
• Peripherals: POR, WDT
• Number Of I /o: 24
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: OTP
• Ram Size: 304 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-PLCC
• A/d Inputs: 4-Channel, 8-Bit
• Eeprom Memory: 0 Bytes
• Input Output: 24
• Interface: SCI/SPI
• Memory Type: OTP
• Number Of Bits: 8
• Package Type: 44-pin PLCC
• Programmable Memory: 8K Bytes
• Timers: 3-16-bit
• Voltage, Range: 3-5.5 V
• Processor Series: HC705C
• Core: HC05
• Data Bus Width: 8 bit
• Data Ram Size: 304 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 2.1 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 1
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: RoHS Compliant part

6.3.4 Non-Programmable COP Watchdog in Stop Mode
6.4 Wait Mode
MC68HC705C8A — Rev. 3
MOTOROLA
NOTE:
The STOP instruction has these effects on the non-programmable COP
watchdog:
If the RESET pin brings the MCU out of stop mode, the COP watchdog
begins counting immediately. The reset function clears the COP counter
again after the 4064-t
If the IRQ pin brings the MCU out of stop mode, the COP watchdog
begins counting immediately. The IRQ function does not clear the
COP counter again after the 4064-t
Figure
If the clock monitor is enabled (CME = 1), the STOP instruction causes
it to time out and reset the MCU.
The WAIT instruction places the MCU in an intermediate power
consumption mode. All central processor unit (CPU) activity is
suspended, but the oscillator, capture/compare timer, SCI, and SPI
remain active. Any interrupt or reset brings the MCU out of wait mode.
See
The WAIT instruction has these effects on the CPU:
The WAIT instruction does not affect any other registers or I/O lines. The
capture/compare timer, SCI, and SPI can be enabled to allow a periodic
exit from wait mode.
•
•
•
•
Freescale Semiconductor, Inc.
Figure
For More Information On This Product,
Turns off the oscillator and the COP watchdog counter
Clears the COP watchdog counter
Clears the I bit in the condition code register, enabling interrupts
Stops the CPU clock, but allows the internal clock to drive the
capture/compare timer, SCI, and SPI
6-3.
6-1.
Go to: www.freescale.com
Low-Power Modes
CYC
clock stabilization delay.
CYC
clock stabilization delay. See
Low-Power Modes
Technical Data
Wait Mode