PIC18LF6310T-I/PT Microchip Technology, PIC18LF6310T-I/PT Datasheet - Page 3

• Manufacturer Part Number: PIC18LF6310T-I/PT
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,TQFP,64PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF6310T-I/PT

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Power-Managed Modes:
• Run: CPU on, Peripherals on
• Idle: CPU off, Peripherals on
• Sleep: CPU off, Peripherals off
• Ultra Low 50 nA Input Leakage
• Idle mode Currents Down to 2.3 A Typical
• Ultra Low 50 nA Input Leakage
• Sleep mode Currents Down to 0.1 A Typical
• Timer1 Oscillator: 1.0 A, 32 kHz, 2V Typical
• Watchdog Timer: 1.7 A Typical
• Two-Speed Oscillator Start-up
Flexible Oscillator Structure:
• Four Crystal modes up to 40 MHz
• 4x Phase Lock Loop (available for crystal and
• Two External RC modes, up to 4 MHz
• Two External Clock modes, up to 40 MHz
• Internal Oscillator Block:
• Secondary Oscillator using Timer1 @ 32 kHz
• Fail-Safe Clock Monitor:
External Memory Interface
(PIC18F8310/8410 Devices only):
• Address Capability of up to 2 Mbytes
• 16-Bit/8-Bit Interface
Peripheral Highlights:
• High-Current Sink/Source 25 mA/25 mA
• Four External Interrupts
• Four Input Change Interrupts
• Four 8-Bit/16-Bit Timer/Counter modules
• Up to 3 Capture/Compare/PWM (CCP) modules
 2010 Microchip Technology Inc.
64/80-Pin Flash Microcontrollers with nanoWatt Technology
PIC18F6310
PIC18F6410
PIC18F8310
PIC18F8410 16K/2M
internal oscillators)
- Fast wake from Sleep and Idle, 1 s typical
- 8 user-selectable frequencies, from 31 kHz to
- Provides a complete range of clock speeds,
- User-tunable to compensate for frequency drift
- Allows for safe shutdown if peripheral clock stops
Device
8 MHz
from 31 kHz to 32 MHz, when used with PLL
(bytes)
8K/2M
16K/0
Flash
8K/0
(On-Board/External)
Program Memory
# Single-Word
Instructions
4096/1M
8192/1M
4096/0
8192/0
PIC18F6310/6410/8310/8410
Memory
(bytes)
SRAM
Data
768
768
768
768
I/O
54
54
70
70
A/D (ch)
10-Bit
12
12
12
12
Peripheral Highlights (Continued):
• Master Synchronous Serial Port (MSSP) module
• Addressable USART module:
• Enhanced Addressable USART module:
• 10-Bit, up to 12-Channel Analog-to-Digital (A/D)
• Dual Analog Comparators with Input Multiplexing
• Programmable 16-Level High/Low-Voltage
Special Microcontroller Features:
• C Compiler Optimized Architecture:
• 1000 Erase/Write Cycle Flash Program Memory
• Flash Retention: 100 Years Typical
• Priority Levels for Interrupts
• 8 x 8 Single-Cycle Hardware Multiplier
• Extended Watchdog Timer (WDT):
• In-Circuit Serial Programming™ (ICSP™) via
• In-Circuit Debug (ICD) via Two Pins
• Wide Operating Voltage Range: 2.0V to 5.5V
• Programmable Brown-out Reset (BOR) with
(PWM)
Supporting 3-Wire SPI (all 4 modes) and I
Master and Slave modes
- Supports RS-485 and RS-232
- Supports RS-485, RS-232 and LIN/J2602
- Auto-Wake-up on Start bit
- Auto-Baud Detect
Converter module:
- Auto-acquisition capability
- Conversion available during Sleep
Detection (HLVD) module:
- Supports interrupt on High/Low-Voltage Detection
- Optional extended instruction set designed to
Typical
- Programmable period from 4 ms to 131s
- 2% stability over V
Two Pins
Software Enable Option
CCP
optimize re-entrant code
3
3
3
3
SPI
Y
Y
Y
Y
MSSP
Master
I
2
C™
Y
Y
Y
Y
DD
and temperature
1/1
1/1
1/1
1/1
2
2
2
2
DS39635C-page 3
8/16-Bit
Timers
1/3
1/3
1/3
1/3
2
C™
Bus
Ext.
N
N
Y
Y