UPD70F3747GB-GAH-AX Renesas Electronics America, UPD70F3747GB-GAH-AX Datasheet - Page 958
UPD70F3747GB-GAH-AX
Manufacturer Part Number
UPD70F3747GB-GAH-AX
Description
MCU 32BIT V850ES/HX3 64-LQFP
Manufacturer
Renesas Electronics America
Series
V850ES/Hx3r
Datasheet
1.UPD70F3747GB-GAH-AX.pdf
(1106 pages)
Specifications of UPD70F3747GB-GAH-AX
Core Processor
RISC
Core Size
32-Bit
Speed
32MHz
Connectivity
CSI, I²C, UART/USART
Peripherals
DMA, LVD, PWM, WDT
Number Of I /o
51
Program Memory Size
128KB (128K x 8)
Program Memory Type
FLASH
Ram Size
8K x 8
Voltage - Supply (vcc/vdd)
3.7 V ~ 5.5 V
Data Converters
A/D 10x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
UPD70F3747GB-GAH-AX
Manufacturer:
Renesas Electronics America
Quantity:
10 000
- Current page: 958 of 1106
- Download datasheet (9Mb)
956
(2) DCK
(3) DMS
(4) DDI
(5) DDO
(6) EV
(7) FLMD0
(8) RESET
This is a clock input signal. It supplies a 20 MHz or 10 MHz clock from MINICUBE. In the on-chip debug unit,
the DMS and DDI signals are sampled at the rising edge of the DCK signal, and the data DDO is output at its
falling edge.
This is a transfer mode select signal. The transfer status in the debug unit changes depending on the level of
the DMS signal.
This is a data input signal. It is sampled in the on-chip debug unit at the rising edge of DCK.
This is a data output signal. It is output from the on-chip debug unit at the falling edge of the DCK signal.
This signal is used to detect VDD of the target system. If VDD from the target system is not detected, the
signals output from MINICUBE (DRST, DCK, DMS, DDI, FLMD0, and RESET) go into a high-impedance state.
The flash self programming function is used for the function to download data to the flash memory via the
integrated debugger. During flash self programming, the FLMD0 pin must be kept high. In addition, connect a
pull-down resistor to the FLMD0 pin.
The FLMD0 pin can be controlled in either of the following two ways.
<1> To control from MINICUBE
<2> To control from port
This is a system reset input pin. If the DRST pin is made invalid by the value of the OCDM0 bit of the OCDM
register set by the user program, on-chip debugging cannot be executed. Therefore, reset is effected by
MINICUBE, using the RESET pin, to make the DRST pin valid (initialization).
DD
For details, refer to the ID850QB Ver. 3.40 Integrated Debugger Operation User's Manual (U18604E).
Connect the FLMD0 signal of MINICUBE to the FLMD0 pin.
In the normal mode, nothing is driven by MINICUBE (high impedance).
During a break, MINICUBE raises the FLMD0 pin to the high level when the download function of the
integrated debugger is executed.
Connect any port of the device to the FLMD0 pin.
The same port as the one used by the user program to realize the flash self programming function may
be used.
On the console of the integrated debugger, make a setting to raise the port pin to high level before
executing the download function, or lower the port pin after executing the download function.
CHAPTER 28 ON-CHIP DEBUG FUNCTION
User’s Manual U18854EJ2V0UD
Related parts for UPD70F3747GB-GAH-AX
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV FOR SH7203
Manufacturer:
Renesas Electronics America
Datasheet: