PIC16F877A-I/PT Microchip Technology Inc., PIC16F877A-I/PT Datasheet - Page 122

• Manufacturer Part Number: PIC16F877A-I/PT
• Description: 44 PIN, 7 KB FLASH, 368 RAM, 33 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F877A-I/PT

• A/d Inputs: 8-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 5 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 33
• Interface: I2C/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 44-pin TQFP
• Programmable Memory: 14K Bytes
• Ram Size: 368 Bytes
• Speed: 20 MHz
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC16F87X
REGISTER 12-1:
DS30292C-page 120
bit13
bit 13-12,
bit 5-4
bit 11
bit 10
bit 9
bit 8
bit 7
bit 6
bit 3
bit 2
bit 1-0
Note 1: The erased (unprogrammed) value of the configuration word is 3FFFh.
CP1
2: All of the CP1:CP0 pairs have to be given the same value to enable the code protection scheme listed.
3: Enabling Brown-out Reset automatically enables Power-up Timer (PWRT), regardless of the value of bit PWRTE.
CP0
Ensure the Power-up Timer is enabled any time Brown-out Reset is enabled.
DEBUG
CP1:CP0: FLASH Program Memory Code Protection bits
11 = Code protection off
10 = 1F00h to 1FFFh code protected (PIC16F877, 876)
10 = 0F00h to 0FFFh code protected (PIC16F874, 873)
01 = 1000h to 1FFFh code protected (PIC16F877, 876)
01 = 0800h to 0FFFh code protected (PIC16F874, 873)
00 = 0000h to 1FFFh code protected (PIC16F877, 876)
00 = 0000h to 0FFFh code protected (PIC16F874, 873)
DEBUG: In-Circuit Debugger Mode
1 = In-Circuit Debugger disabled, RB6 and RB7 are general purpose I/O pins
0 = In-Circuit Debugger enabled, RB6 and RB7 are dedicated to the debugger.
Unimplemented: Read as ‘1’
WRT: FLASH Program Memory Write Enable
1 = Unprotected program memory may be written to by EECON control
0 = Unprotected program memory may not be written to by EECON control
CPD: Data EE Memory Code Protection
1 = Code protection off
0 = Data EEPROM memory code protected
LVP: Low Voltage In-Circuit Serial Programming Enable bit
1 = RB3/PGM pin has PGM function, low voltage programming enabled
0 = RB3 is digital I/O, HV on MCLR must be used for programming
BODEN: Brown-out Reset Enable bit
1 = BOR enabled
0 = BOR disabled
PWRTE: Power-up Timer Enable bit
1 = PWRT disabled
0 = PWRT enabled
WDTE: Watchdog Timer Enable bit
1 = WDT enabled
0 = WDT disabled
FOSC1:FOSC0: Oscillator Selection bits
11 = RC oscillator
10 = HS oscillator
01 = XT oscillator
00 = LP oscillator
CONFIGURATION WORD (ADDRESS 2007h)
—
WRT
CPD
(3)
LVP
(3)
BODEN
CP1
(2)
CP0
(1)
PWRTE
2001 Microchip Technology Inc.
WDTE
F0SC1
F0SC0
bit0