TMPM370FYDFG Toshiba, TMPM370FYDFG Datasheet - Page 114

• Manufacturer Part Number: TMPM370FYDFG
• Description: Microcontrollers (MCU) MCU w/ ARM Cortex-M3 256K FLASH, 10K RAM
• Manufacturer: Toshiba

Specifications of TMPM370FYDFG

• Processor Series: TX03
• Core: ARM Cortex M3
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 256K
• Rom Type: Flash
• Ram (kbytes): 10K
• Number Of Pins: 100
• Package: QFP(14x20)
• Vcc: 5V
• Cpu Mhz: 80
• Ssp (ch) Spi: -
• I2c/sio (ch): -
• Uart/sio (ch): 4
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: N
• Cs/wait Controller (ch): -
• Dma Controller: -
• 10-bit Da Converter: -
• 10-bit Ad Converter: -
• 12-bit Ad Converter: 27
• 16-bit Timer / Counter: 8
• Motor / Igbt Control: Vector Engine
• Real Time Clock: -
• Watchdog Timer: Y
• Osc Freq Detect: Y
• Clock Gear: Y
• Low-power Hold Function: -
• Remote Control Interface: -
• Hardware Cec Controller: -
• Comparators: 4
• Low-voltage Detector: Y
• Etm Hardware Trace: 2-bit
• Lead Free Status / Rohs Status: Details

PHFR1
(0x4000_01C8)
PHDATA
(0x4000_01C0)
PHCR
(0x4000_01C4)
8.2.9
specified in units of bits. Besides the general-purpose input/output function, the port H performs the
analog input of the A/D converter and the external interrupt input.
pull-down disabled.
and enable input in the PHIE register. These settings enable the interrupt input even if the
CGSTBYCR<DRVE> bit in the clock/mode control block is set to stop driving of pins during STOP
mode.
(Note 1) In modes other than STOP mode, interrupt input is enabled regardless of the PxFR
(Note 2) Unless you use all the bits of port H as analog input pins, conversion accuracy may be
The port H is a general-purpose 8-bit input/output port. For this port, inputs and outputs can be
Reset initializes all bits of the port H as general-purpose ports with input, output, pull-up and
To use the external interrupt input for releasing STOP mode, select this function in the PHFR1 register
Port H (PH0 to PH7)
Bit Symbol
Read/Write
After reset
Function
Bit Symbol
Read/Write
After reset
Bit Symbol
Read/Write
After reset
Function
register setting as long as input is enabled in PxIE. Make sure to disable unused
interrupts when programming the device.
reduced. Be sure to verify that this causes no problem on your system.
Type
PH7C
PH7
T16
7
7
7
7
0
0
-
PH6C
PH6
T16
6
0
6
6
6
Port H function register 1
0
-
Port H control register
Port H circuit type
TMPM370 8-17
Port H register
“0” is read
PH5C
PH5
T16
R
5
5
5
5
0
0
-
PH4C
PH4
T16
4
4
4
4
0
0
-
0: disabled
1: enabled
Output
R/W
R/W
“0”
PH3C
PH3
T16
3
3
3
3
0
0
-
0:PORT
1:INT2
PH2F1
PH2C
PH2
T17
2
2
2
2
0
0
Input/Output Ports
0:PORT
1:INT1
PH1F1
PH1C
R/W
PH1
T17
1
1
1
1
0
0
TMPM370
0:PORT
1:INT0
PH0F1
PH0C
T17
PH0
0
0
0
0
0
0