S9S12G128F0VLL Freescale Semiconductor, S9S12G128F0VLL Datasheet - Page 631

no-image

S9S12G128F0VLL

Manufacturer Part Number
S9S12G128F0VLL
Description
16-bit Microcontrollers - MCU 16BIT 128K FLASH
Manufacturer
Freescale Semiconductor
Datasheet

Specifications of S9S12G128F0VLL

Rohs
yes
Core
S12
Processor Series
MC9S12G
Data Bus Width
16 bit
Maximum Clock Frequency
1 MHz
Program Memory Size
128 KB
Data Ram Size
8 KB
On-chip Adc
Yes
Operating Supply Voltage
3.13 V to 5.5 V
Operating Temperature Range
- 40 C to + 125 C
Package / Case
LQFP-100
Mounting Style
SMD/SMT
A/d Bit Size
10 bit, 12 bit
A/d Channels Available
12
Interface Type
SPI
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Number Of Programmable I/os
86
Number Of Timers
8
Program Memory Type
Flash
Supply Voltage - Max
5.5 V
Supply Voltage - Min
3.13 V

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
S9S12G128F0VLL
Manufacturer:
FREESCALE
Quantity:
2 250
Part Number:
S9S12G128F0VLL
Manufacturer:
FREESCALE
Quantity:
2 250
Part Number:
S9S12G128F0VLLR
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
If the WUPE bit in CANCTL0 is not asserted, the MSCAN will mask any activity it detects on CAN.
RXCAN is therefore held internally in a recessive state. This locks the MSCAN in sleep mode. WUPE
must be set before entering sleep mode to take effect.
The MSCAN is able to leave sleep mode (wake up) only when:
After wake-up, the MSCAN waits for 11 consecutive recessive bits to synchronize to the CAN bus. As a
consequence, if the MSCAN is woken-up by a CAN frame, this frame is not received.
The receive message buffers (RxFG and RxBG) contain messages if they were received before sleep mode
was entered. All pending actions will be executed upon wake-up; copying of RxBG into RxFG, message
aborts and message transmissions. If the MSCAN remains in bus-off state after sleep mode was exited, it
continues counting the 128 occurrences of 11 consecutive recessive bits.
18.4.5.6
The MSCAN is in power down mode
When entering the power down mode, the MSCAN immediately stops all ongoing transmissions and
receptions, potentially causing CAN protocol violations. To protect the CAN bus system from fatal
consequences of violations to the above rule, the MSCAN immediately drives TXCAN into a recessive
state.
In power down mode, all clocks are stopped and no registers can be accessed. If the MSCAN was not in
sleep mode before power down mode became active, the module performs an internal recovery cycle after
powering up. This causes some fixed delay before the module enters normal mode again.
Freescale Semiconductor
CAN bus activity occurs and WUPE = 1
or
the CPU clears the SLPRQ bit
CPU is in stop mode
or
CPU is in wait mode and the CSWAI bit is set
MSCAN Power Down Mode
The CPU cannot clear the SLPRQ bit before sleep mode (SLPRQ = 1 and
SLPAK = 1) is active.
The user is responsible for ensuring that the MSCAN is not active when
power down mode is entered. The recommended procedure is to bring the
MSCAN into Sleep mode before the STOP or WAI instruction (if CSWAI
is set) is executed. Otherwise, the abort of an ongoing message can cause an
error condition and impact other CAN bus devices.
MC9S12G Family Reference Manual, Rev.1.23
(Table
18-38) when
NOTE
NOTE
Freescale’s Scalable Controller Area Network (S12MSCANV3)
633

Related parts for S9S12G128F0VLL