PIC12C672-10/SM Microchip Technology, PIC12C672-10/SM Datasheet - Page 325

• Manufacturer Part Number: PIC12C672-10/SM
• Description: IC MCU OTP 2KX14 A/D 8-SOIJ
• Manufacturer: Microchip Technology
• Series: PIC® 12Cr

Specifications of PIC12C672-10/SM

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 10MHz
• Peripherals: POR, WDT
• Number Of I /o: 5
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: OTP
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 4x8b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
• For Use With: XLT08SO-1 - SOCKET TRANSITION 8SOIC 150/208AC164312 - MODULE SKT FOR PM3 16SOICISPICR1 - ADAPTER IN-CIRCUIT PROGRAMMING309-1048 - ADAPTER 8-SOIC TO 8-DIP309-1047 - ADAPTER 8-SOIC TO 8-DIPAC124001 - MODULE SKT PROMATEII 8DIP/SOIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Other names: PIC12C672-10/SMR; PIC12C672-10/SMR

17.4.18
1997 Microchip Technology Inc.
SDA
SCL
BCLIF
Multi -Master Communication, Bus Collision, and Bus Arbitration
Multi-Master mode support is achieved by bus arbitration. When the master outputs address/data
bits onto the SDA pin, arbitration takes place when the master outputs a '1' on SDA by letting
SDA float high and another master asserts a '0'. When the SCL pin floats high, data should be
stable. If the expected data on SDA is a '1' and the data sampled on the SDA pin = '0', then a bus
collision has taken place. The master will set the Bus Collision Interrupt Flag, BCLIF and reset
the I
If a transmit was in progress when the bus collision occurred, the transmission is halted, the BF
flag is cleared, the SDA and SCL lines are de-asserted, and the SSPBUF can be written to. When
the user services the bus collision interrupt service routine, and if the I
can resume communication by asserting a START condition.
If a START, Repeated Start, STOP, or Acknowledge condition was in progress when the bus col-
lision occurred, the condition is aborted, the SDA and SCL lines are de-asserted, and the respec-
tive control bits in the SSPCON2 register are cleared. When the user services the bus collision
interrupt service routine, and if the I
ing a START condition.
The Master will continue to monitor the SDA and SCL pins, and if a STOP condition occurs, the
SSPIF bit will be set.
A write to the SSPBUF will start the transmission of data at the first data bit, regardless of where
the transmitter left off when bus collision occurred.
In multi-master mode, the interrupt generation on the detection of start and stop conditions allows
the determination of when the bus is free. Control of the I
set in the SSPSTAT register, or the bus is idle and the S and P bits are cleared.
Figure 17-34: Bus Collision Timing for Transmit and Acknowledge
2
C port to its IDLE state.
Data changes
while SCL = 0
SDA released
by master
Preliminary
(Figure
SDA line pulled low
by another source
2
C bus is free, the user can resume communication by assert-
17-34).
Section 17. MSSP
Sample SDA. While SCL is high
data doesn’t match what is driven
by the master.
Bus collision has occurred.
2
C bus can be taken when the P bit is
Set bus collision
interrupt (BCLIF).
2
C bus is free, the user
DS31017A-page 17-49
17