MC9RS08KA2CSCR Freescale Semiconductor, MC9RS08KA2CSCR Datasheet - Page 109

• Manufacturer Part Number: MC9RS08KA2CSCR
• Description: IC MCU 8BIT 2K FLASH 8-SOIC
• Manufacturer: Freescale Semiconductor
• Series: RS08r

Specifications of MC9RS08KA2CSCR

• Core Processor: RS08
• Core Size: 8-Bit
• Speed: 10MHz
• Peripherals: LVD, POR, WDT
• Number Of I /o: 4
• Program Memory Size: 2KB (2K x 8)
• Program Memory Type: FLASH
• Ram Size: 63 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Processor Series: RS08KA
• Core: RS08
• Data Bus Width: 8 bit
• Data Ram Size: 63 B
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 4
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: DEMO9RS08KA8, DEMO9RS08KA2
• Minimum Operating Temperature: - 40 C
• For Use With: DEMO9RS08KA2 - DEMO BOARD FOR 9RS08KA2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

Appendix A
Electrical Characteristics
A.1
This chapter contains electrical and timing specifications.
A.2
Absolute maximum ratings are stress ratings only, and functional operation at the maxima is not
guaranteed. Stress beyond the limits specified in
permanent damage to the device. For functional operating conditions, refer to the remaining tables in this
chapter.
This device contains circuitry protecting against damage due to high static voltage or electrical fields;
however, it is advised that normal precautions be taken to avoid application of any voltages higher than
maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused
inputs are tied to an appropriate logic voltage level (for instance, either V
pull-up resistor associated with the pin is enabled.
1
2
3
Freescale Semiconductor
Supply voltage
Maximum current into V
Digital input voltage
Instantaneous maximum current
Storage temperature range
Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate
resistance values for positive (V
All functional non-supply pins are internally clamped to V
to V
Power supply must maintain regulation within operating V
conditions. If positive injection current (V
in external power supply going out of regulation. Ensure external V
current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is present, or
if the clock rate is very low which would reduce overall power consumption.
Single pin limit (applies to all port pins)
SS
only.
Introduction
Absolute Maximum Ratings
DD
Rating
DD
) and negative (V
Table A-1. Absolute Maximum Ratings
MC9RS08KA2 Series Data Sheet, Rev. 4
1, 2, 3
In
> V
DD
) is greater than I
SS
) clamp voltages, then use the larger of the two resistance values.
Table A-1
SS
DD
and V
range during instantaneous and operating maximum current
DD
DD
DD
, the injection current may flow out of V
except the RESET/V
may affect device reliability or cause
load will shunt current greater than maximum injection
Symbol
V
T
I
V
DD
I
DD
stg
D
In
SS
or V
–0.3 to V
PP
–0.3 to +5.8
–55 to 150
pin which is internally clamped
DD
Value
± 25
120
) or the programmable
DD
+ 0.3
DD
and could result
Unit
mA
mA
°C
V
V
109