MC9RS08KA2CSCR Freescale Semiconductor, MC9RS08KA2CSCR Datasheet - Page 81

• Manufacturer Part Number: MC9RS08KA2CSCR
• Description: IC MCU 8BIT 2K FLASH 8-SOIC
• Manufacturer: Freescale Semiconductor
• Series: RS08r

Specifications of MC9RS08KA2CSCR

• Core Processor: RS08
• Core Size: 8-Bit
• Speed: 10MHz
• Peripherals: LVD, POR, WDT
• Number Of I /o: 4
• Program Memory Size: 2KB (2K x 8)
• Program Memory Type: FLASH
• Ram Size: 63 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Processor Series: RS08KA
• Core: RS08
• Data Bus Width: 8 bit
• Data Ram Size: 63 B
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 4
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: DEMO9RS08KA8, DEMO9RS08KA2
• Minimum Operating Temperature: - 40 C
• For Use With: DEMO9RS08KA2 - DEMO BOARD FOR 9RS08KA2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

9.4.1.4
ICS stop mode is entered whenever the MCU enters stop. In this mode, all ICS clocks are stopped except
ICSIRCLK which will remaining running if IREFSTEN is written to a 1.
When the MCU is interrupted from stop, the ICS will go back to the operating mode that was running when
the MCU entered stop. If the internal reference was not running in stop (IREFSTEN = 0), the ICS will take
some time, t
(IREFSTEN = 1), entering into FEI will take some time, t
frequency.
9.4.2
When changing from FBILP to either FEI or FBI, or anytime the trim value is written, the user should wait
the FLL acquisition time, t
9.4.3
The BDIV bits can be changed at anytime and the actual switch to the new frequency will occur
immediately.
9.4.4
The low power bit (LP) is provided to allow the FLL to be disabled and thus conserve power when it is
not being used. However, in some applications it may be desirable to enable the FLL and allow it to lock
for maximum accuracy before switching to an FLL engaged mode. The FLL is disabled in bypass mode
when LP = 1.
9.4.5
The ICSIRCLK frequency can be re-targeted by trimming the period of the internal reference clock. This
can be done by writing a new value to the TRIM bits in the ICSTRM register. Writing a larger value will
slow down the ICSIRCLK frequency, and writing a smaller value to the ICSTRM register will speed up
the ICSIRCLK frequency. The TRIM bits will affect the ICSOUT frequency if the ICS is in FLL engaged
internal (FEI), FLL bypassed internal (FBI), or FLL bypassed internal low power (FBILP) mode. The
TRIM and FTRIM values will not be affected by a reset. For the ICS to run in stop, the LVDE and LVDSE
bits in the SPMSC1 must both be set before entering stop.
Until ICSIRCLK is trimmed, ICSOUT frequencies may exceed the maximum chip-level frequency and
violate the chip-level clock timing specifications (see the
a divide by 2 to prevent the bus frequency from exceeding the maximum. The user should trim the device
to an allowable frequency before changing BDIV to a divide by 1 operation.
Freescale Semiconductor
ir_wu
Mode Switching
Bus Frequency Divider
Low Power Bit Usage
Internal Reference Clock
Stop
, for the internal reference to wakeup. If the internal reference was already running in stop
acquire
, before FLL will be guaranteed to be at desired frequency.
MC9RS08KA2 Series Data Sheet, Rev. 4
fll_wu
Device Overview
, for the FLL to return its previous acquired
chapter). The BDIV is reset to
Internal Clock Source (RS08ICSV1)
81