C8051F130-GQR Silicon Laboratories Inc, C8051F130-GQR Datasheet - Page 201

• Manufacturer Part Number: C8051F130-GQR
• Description: IC 8051 MCU 128K FLASH 100TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F13xr

Specifications of C8051F130-GQR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 100MHz
• Connectivity: EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 64
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8.25K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• Processor Series: C8051F1x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 8.25 KB
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Clock Frequency: 100 MHz
• Number Of Programmable I/os: 64
• Number Of Timers: 5
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F120DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

15.1.2. Erasing Flash Pages From Software
When erasing Flash memory, an entire page is erased (all bytes in the page are set to 0xFF). The Flash
memory is organized in 1024-byte pages. The 256 bytes of Scratchpad area (addresses 0x20000 to
0x200FF) consists of two 128 byte pages. To erase any Flash page, the FLWE, PSWE, and PSEE bits
must be set to ‘1’, and a byte must be written using a MOVX instruction to any address within that page.
The following is the recommended procedure for erasing a Flash page from software:
Figure 15.1. Flash Memory Map for MOVC Read and MOVX Write Operations
Step 1. Disable interrupts.
Step 2. If erasing a page in Bank 1, Bank 2, or Bank 3, set the COBANK bits (PSBANK.5-4) for
Step 3. If erasing a page in the Scratchpad area, set the SFLE bit (PSCTL.2).
Step 4. Set FLWE (FLSCL.0) to enable Flash writes/erases via user software.
Step 5. Set PSEE (PSCTL.1) to enable Flash erases.
Step 6. Set PSWE (PSCTL.0) to redirect MOVX commands to write to Flash.
Step 7. Use the MOVX instruction to write a data byte to any location within the page to be
Step 8. Clear PSEE to disable Flash erases.
Step 9. Clear the PSWE bit to redirect MOVX commands to the XRAM data space.
Step 10. Clear the FLWE bit, to disable Flash writes/erases.
Step 11. If erasing a page in the Scratchpad area, clear the SFLE bit.
Step 12. Re-enable interrupts.
the appropriate bank.
erased.
COBANK = 0 COBANK = 1 COBANK = 2 COBANK = 3
Bank 0
Bank 0
Bank 1
Bank 0
SFLE = 0
128k FLASH devices only.
Bank 2
Bank 0
Rev. 1.4
C8051F120/1/2/3/4/5/6/7
Bank 3
Bank 0
Scratchpad
Undefined
SFLE = 1
Areas (2)
C8051F130/1/2/3
Address
0xFFFF
Internal
0x7FFF
0x00FF
0x8000
0x0000
201