PIC17LC752T-08I/L Microchip Technology, PIC17LC752T-08I/L Datasheet - Page 173

• Manufacturer Part Number: PIC17LC752T-08I/L
• Description: IC MCU OTP 8KX16 A/D 68PLCC
• Manufacturer: Microchip Technology
• Series: PIC® 17Cr

Specifications of PIC17LC752T-08I/L

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 50
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: OTP
• Ram Size: 678 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 68-PLCC
• Processor Series: PIC17LC
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 678 B
• Interface Type: I2C, MSSP, RS- 232, SCI, SPI, USART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 50
• Number Of Timers: 8
• Operating Supply Voltage: 3 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ICE2000, DM173001
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

15.2.18.2
During a Repeated Start condition, a bus collision
occurs if:
a)
b)
When the user de-asserts SDA and the pin is allowed
to float high, the BRG is loaded with SSPADD<6:0>
and counts down to ‘0’. The SCL pin is then de-
asserted and when sampled high, the SDA pin is sam-
pled. If SDA is low, a bus collision has occurred (i.e.,
another master is attempting to transmit a data ’0’). If,
however, SDA is sampled high, then the BRG is
FIGURE 15-38:
FIGURE 15-39:
2000 Microchip Technology Inc.
A low level is sampled on SDA when SCL goes
from low level to high level.
SCL goes low before SDA is asserted low, indi-
cating that another master is attempting to trans-
mit a data ’1’.
SDA
SCL
BCLIF
RSEN
S
SSPIF
SDA
SCL
RSEN
BCLIF
S
SSPIF
Bus Collision During a Repeated
Start Condition
’0’
’0’
’0’
’0’
BUS COLLISION DURING A REPEATED START CONDITION (CASE 1)
BUS COLLISION DURING REPEATED START CONDITION (CASE 2)
SCL goes low before SDA,
Set BCLIF. Release SDA and SCL.
T
BRG
Sample SDA when SCL goes high.
If SDA = 0, set BCLIF and release SDA and SCL.
reloaded and begins counting. If SDA goes from high to
low before the BRG times out, no bus collision occurs
because no two masters can assert SDA at exactly the
same time.
If, however, SCL goes from high to low before the BRG
times out and SDA has not already been asserted, then
a bus collision occurs. In this case, another master is
attempting to transmit a data ’1’ during the Repeated
Start condition.
If, at the end of the BRG time-out, both SCL and SDA
are still high, the SDA pin is driven low, the BRG is
reloaded and begins counting. At the end of the count,
regardless of the status of the SCL pin, the SCL pin is
driven low and the Repeated Start condition is com-
plete (Figure 15-38).
T
Cleared in software.
BRG
PIC17C7XX
Interrupt cleared
in software.
’0’
’0’
DS30289B-page 173
’0’
’0’