MC68HC705JP7CDW Freescale Semiconductor, MC68HC705JP7CDW Datasheet - Page 97

• Manufacturer Part Number: MC68HC705JP7CDW
• Description: IC MCU 8BIT 28-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC05r

Specifications of MC68HC705JP7CDW

• Core Processor: HC05
• Core Size: 8-Bit
• Speed: 2.1MHz
• Connectivity: SIO
• Peripherals: POR, Temp Sensor, WDT
• Number Of I /o: 22
• Program Memory Size: 6KB (6K x 8)
• Program Memory Type: OTP
• Ram Size: 224 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 4x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

9.2.2 Serial Data Input (SDI)
The SDI pin becomes an input as soon as the SIOP subsystem is enabled. New data is presented to the
SDI pin on the falling edge of SCK. Valid data must be present at least 100 nanoseconds before the rising
edge of SCK and remain valid for 100 nanoseconds after the rising edge of SCK. See
9.2.3 Serial Data Output (SDO)
The SDO pin becomes an output as soon as the SIOP subsystem is enabled. The state of the PB5/SDO
pin reflects the value of the first bit received on the previous transmission. Prior to enabling the SIOP, the
PB5/SDO can be initialized to determine the beginning state. While SIOP is enabled, the port B logic
cannot be used as a standard output since that pin is connected to the last stage of the SIOP serial shift
register. A control bit (LSBF) is included in the SCR to allow the data to be transmitted in either the MSB
first format or the LSB first format.
The first data bit will be shifted out to the SDO pin on the first falling edge of the SCK. The remaining data
bits will be shifted out to the SDI pin on subsequent falling edges of SCK. The SDO pin will present valid
data at least 100 nanoseconds before the rising edge of the SCK and remain valid for 100 nanoseconds
after the rising edge of SCK. See
9.3 SIOP Registers
The SIOP is programmed and controlled by the SIOP control register (SCR) located at address $000A,
the SIOP status register (SSR) located at address $000B, and the SIOP data register (SDR) located at
address $000C.
9.3.1 SIOP Control Register (SCR)
The SIOP control register (SCR) is located at address $000A and contains seven control bits and a
write-only reset of the interrupt flag.
the value of each bit after reset.
SPIE — Serial Peripheral Interrupt Enable Bit
Freescale Semiconductor
The SPIE bit enables the SIOP to generate an interrupt whenever the SPIF flag bit in the SSR is set.
Clearing the SPIE bit will not affect the state of the SPIF flag bit and will not terminate a serial interrupt
once the interrupt sequence has started. Reset clears the SPIE bit.
1 = Serial interrupt enabled
0 = Serial interrupt disabled
Address:
If the SPIE bit is cleared just after the serial interrupt sequence has started
(for instance, the CPU status is being stacked), then the CPU will be unable
Reset:
Read:
Write:
MC68HC705JJ7 • MC68HC705JP7 Advance Information Data Sheet, Rev. 4.1
$000A
SPIE
Bit 7
0
Figure 9-4. SIOP Control Register (SCR)
SPE
Figure
6
0
Figure 9-4
9-3.
LSBF
5
0
shows the position of each bit in the register and indicates
NOTE
MSTR
4
0
SPIR
3
0
0
CPHA
2
0
SPR1
1
0
SPR0
Figure
Bit 0
0
SIOP Registers
9-3.
97