AGLN030V2-ZVQG100 Actel, AGLN030V2-ZVQG100 Datasheet - Page 18

• Manufacturer Part Number: AGLN030V2-ZVQG100
• Description: FPGA - Field Programmable Gate Array 30K System Gates IGLOO nano
• Manufacturer: Actel

Specifications of AGLN030V2-ZVQG100

• Processor Series: AGLN030
• Core: IP Core
• Number Of Macrocells: 256
• Maximum Operating Frequency: 250 MHz
• Number Of Programmable I/os: 77
• Supply Voltage (max): 1.5 V
• Supply Current: 6 uA
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: - 20 C
• Development Tools By Supplier: AGLN-Nano-Kit, AGLN-Z-Nano-Kit, AGL-Dev-Kit-SCS, Silicon-Explorer II, Silicon-Sculptor 3, SI-EX-TCA, FLASHPRO 4, FlashPro 3, FLASHPRO LITE
• Mounting Style: SMD/SMT
• Supply Voltage (min): 1.2 V
• Number Of Gates: 30 K
• Package / Case: VQFP-100
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

IGLOO nano DC and Switching Characteristics
Figure 2-1 • V5 Devices – I/O State as a Function of VCCI and VCC Voltage Levels
2- 4
Deactivation trip point:
Activation trip point:
V
V
a
d
= 0.85 V ± 0.25 V
= 0.75 V ± 0.25 V
VCC = 1.575 V
VCC = 1.425 V
PLL Behavior at Brownout Condition
Actel recommends using monotonic power supplies or voltage regulators to ensure proper power-up
behavior. Power ramp-up should be monotonic at least until VCC and VCCPLX exceed brownout
activation levels (see
When PLL power supply voltage and/or VCC levels drop below the VCC brownout levels (0.75 V ± 0.25
V for V5 devices, and 0.75 V ± 0.2 V for V2 devices), the PLL output lock signal goes LOW and/or the
output clock is lost. Refer to the "Brownout Voltage" section in the "Power-Up/-Down Behavior of Low
Power Flash Devices" chapter of the
and lock recovery.
Internal Power-Up Activation Sequence
To make sure the transition from input buffers to output buffers is clean, ensure that there is no path
longer than 100 ns from input buffer to output buffer in your design.
VCC
1. Core
2. Input buffers
3. Output buffers, after 200 ns delay from input buffer activation
Region 1: I/O Buffers are OFF
VCC = VCCI + VT
where VT can be from 0.58 V to 0.9 V (typically 0.75 V)
Deactivation trip point:
Activation trip point:
V
V
d
a
= 0.9 V ± 0.3 V
= 0.8 V ± 0.3 V
Figure 2-1
Region 1: I/O buffers are OFF
Region 2: I/O buffers are ON.
I/Os are functional but slower because
VCCI / VCC are below specification. For the
same reason, input buffers do not meet
VIH/VIL levels, and output buffers to not
meet VOH / VOL levels.
buffers do not meet VOH/VOL levels.
and
meet VIH / VIL levels, and output
same reason, input buffers do not
Figure 2-2 on page 2-5
is below specification. For the
IGLOO nano FPGA Fabric User’s Guide
but slower because VCCI
R ev isio n 1 1
I/Os are functional
buffers are ON.
Region 4: I/O
Min VCCI datasheet specification
standard; i.e., 1.425 V or 1.7 V
voltage at a selected I/O
or 2.3 V or 3.0 V
for more details).
Region 3: I/O buffers are ON.
I/Os are functional; I/O DC
specifications are met,
but I/Os are slower because
the VCC is below specification.
Region 5: I/O buffers are ON
and power supplies are within
specification.
I/Os meet the entire datasheet
and timer specifications for
speed, VIH / VIL , VOH / VOL , etc.
for information on clock
V
CCI