LAN9118-MD SMSC, LAN9118-MD Datasheet - Page 30

• Manufacturer Part Number: LAN9118-MD
• Description: Ethernet ICs HiPerfrm Sngl-Chip 10/100 Ethrnt
• Manufacturer: SMSC
• Type: Single Chip MAC and PHYr

Specifications of LAN9118-MD

• Ethernet Connection Type: 10 Base-T, 100 Base-TX
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Product: Ethernet Controllers
• Number Of Transceivers: 1
• Standard Supported: 802.3
• Data Rate: 10 MB, 100 MB
• Supply Voltage (max): 3.3 V
• Supply Voltage (min): 0 V
• Maximum Operating Temperature: + 70 C
• Package / Case: TQFP-100
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Revision 1.5 (07-11-08)
3.6
3.6.1
3.6.2
3.7
Destination Address Source Address ……………FF FF FF FF FF FF
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
…CRC
It should be noted that Magic Packet detection can be performed when LAN9118 is in the D0 or D1
power states. In the D0 state, “Magic Packet” detection is enabled when the MPEN bit is set. In the
D1 state, Magic Packet detection, as well as wake-up frame detection, are automatically enabled when
the device enters the D1 state.
The LAN9118 can be configured to communicate with the host bus via either a 32-bit or a 16-bit bus.
An external strap is used to select between the two modes. 32-bit mode is the native environment for
the LAN9118 Ethernet controller and no special requirements exist for communication in this mode.
However, when this part is used in the 16-bit mode, two writes or reads must be performed back to
back to properly communicate.
The bus width is set by strapping the EEDIO pin; this setting can be read from bit 2 of the “Hardware
Configuration Register”. Please refer to
on page 77
16-bit Bus Writes
The host processor is required to perform two contiguous 16-bit writes to complete a single DWORD
transfer. This DWORD must begin and end on a DWORD address boundary (A[2] and higher, cannot
change during a sixteen bit write). No ordering requirements exist. The processor can access either
the low or high word first, as long as the next write is performed to the other word. If a write to the
same word is performed, the LAN9118 disregards the transfer.
16-bit Bus Reads
The host processor is required to perform two consecutive 16-bit reads to complete a single DWORD
transfer. This DWORD must begin and end on a DWORD address boundary (A[2] and higher, cannot
change during a sixteen bit read). No ordering requirements exist. The processor can access either
the low or high word first, as long as the next read is performed from the other word. If a read to the
same word is performed, the data read is invalid and should be re-read. This is not a fatal error. The
LAN9118 will reset its read counters and restart a new cycle on the next read. The Upper 16 data pins
(D[31:16]) are not driven by the LAN9118 in 16-bit mode. These pins have internal pull-down’s and the
signals are left in a high-impedance state.
The SMSC LAN9118 supports “Big-” or “Little-Endian” processors in either 16 or 32-bit bus width
modes. To support big-endian processors, the hardware designer must explicitly invert the layout of
the byte lanes. In addition, for a 16-bit interface, the
correctly following
The host bus interface can be selected via an external strap to translate the data bus into either mode.
Please refer to
multiplexed signal D32/nD16 for more information on data bus width selection.
32-bit vs. 16-bit Host Bus Width Operation
Big and Little Endian Support
for additional information on this register.
Table 2.4, “Serial EEPROM Interface Signals,” on page
Table 3.7, "Byte Lane
DATASHEET
Section 5.3.9, "HW_CFG—Hardware Configuration Register,"
Mapping".
30
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
WORD_SWAP—Word Swap Control
16, for information on
SMSC LAN9118
must be set
Datasheet