MT41J256M8HX-15E:D Micron Technology Inc, MT41J256M8HX-15E:D Datasheet - Page 166

• Manufacturer Part Number: MT41J256M8HX-15E:D
• Description: MICMT41J256M8HX-15E:D 2GB:X4,X8,X16 DDR3
• Manufacturer: Micron Technology Inc
• Type: DDR3 SDRAMr
• Series: -r

Specifications of MT41J256M8HX-15E:D

• Organization: 256Mx8
• Address Bus: 18b
• Maximum Clock Rate: 1.333GHz
• Operating Supply Voltage (typ): 1.5V
• Package Type: FBGA
• Operating Temp Range: 0C to 95C
• Operating Supply Voltage (max): 1.575V
• Operating Supply Voltage (min): 1.425V
• Supply Current: 165mA
• Pin Count: 78
• Mounting: Surface Mount
• Operating Temperature Classification: Commercial
• Format - Memory: RAM
• Memory Type: DDR3 SDRAM
• Memory Size: 2G (256M x 8)
• Speed: 667MHz
• Interface: Parallel
• Voltage - Supply: 1.425 V ~ 1.575 V
• Operating Temperature: 0°C ~ 95°C
• Package / Case: 78-TFBGA
• Lead Free Status / RoHS Status: Compliant

WRITE Operation
PDF: 09005aef826aaadc
2Gb_DDR3_SDRAM.pdf – Rev. K 04/10 EN
WRITE bursts are initiated with a WRITE command. The starting column and bank ad-
dresses are provided with the WRITE command, and auto precharge is either enabled
or disabled for that access. If auto precharge is selected, the row being accessed will be
precharged at the end of the WRITE burst. If auto precharge is not selected, the row will
remain open for subsequent accesses. After a WRITE command has been issued, the
WRITE burst may not be interrupted. For the generic WRITE commands used in Fig-
ure 84 (page 168) through Figure 92 (page 173), auto precharge is disabled.
During WRITE bursts, the first valid data-in element is registered on a rising edge of
DQS following the WRITE latency (WL) clocks later and subsequent data elements will
be registered on successive edges of DQS. WRITE latency (WL) is defined as the sum of
POSTED CAS ADDITIVE latency (AL) and CAS WRITE latency (CWL): WL = AL + CWL.
The values of AL and CWL are programmed in the MR0 and MR2 registers, respectively.
Prior to the first valid DQS edge, a full cycle is needed (including a dummy crossover of
DQS, DQS#) and specified as the WRITE preamble shown in Figure 84 (page 168). The
half cycle on DQS following the last data-in element is known as the WRITE postamble.
The time between the WRITE command and the first valid edge of DQS is WL clocks
±
where
(MAX) cases.
Data may be masked from completing a WRITE using data mask. The mask occurs on
the DM ball aligned to the write data. If DM is LOW, the write completes normally. If
DM is HIGH, that bit of data is masked.
Upon completion of a burst, assuming no other commands have been initiated, the DQ
will remain High-Z, and any additional input data will be ignored.
Data for any WRITE burst may be concatenated with a subsequent WRITE command to
provide a continuous flow of input data. The new WRITE command can be
following the previous WRITE command. The first data element from the new burst is
applied after the last element of a completed burst. Figure 85 (page 169) and Figure 86
(page 169) on Figure 86 (page 169) show concatenated bursts. An example of noncon-
secutive WRITEs is shown in Figure 87 (page 170).
Data for any WRITE burst may be followed by a subsequent READ command after
has been met (see Figure 88 (page 170) and Figure 89 (page 171) on Figure 89
(page 171) and Figure 90 (page 172)).
Data for any WRITE burst may be followed by a subsequent PRECHARGE command
providing
(page 173).
Both
(fixed BC4, BL8 versus OTF).
t
DQSS. Figure 85 (page 169) through Figure 92 (page 173) show the nominal case
t
WTR and
t
DQSS = 0ns; however, Figure 84 (page 168) includes
t
WR has been met, as shown in Figure 91 (page 173) and Figure 92
t
WR starting time may vary depending on the mode register settings
166
Micron Technology, Inc. reserves the right to change products or specifications without notice.
2Gb: x4, x8, x16 DDR3 SDRAM
t
DQSS (MIN) and
© 2006 Micron Technology, Inc. All rights reserved.
WRITE Operation
t
CCD clocks
t
DQSS
t
WTR