MSO-0008P-012 NCC, MSO-0008P-012 Datasheet - Page 26

• Manufacturer Part Number: MSO-0008P-012
• Description: Socket, Relay; 8 Pin Octal
• Manufacturer: NCC
• Type: Octalr

Specifications of MSO-0008P-012

• Number Of Contacts: 8
• Time Range: 0.05 Sec. to 999 Min.
• Output Rating: 10 A @ 240 VAC Max.; 100 mA @ 5 VDC Min.
• Operating Temperature: –23°C to +55°C

AMETEK National Controls Corp. • 1725 Western Drive • West Chicago, Illinois 60185 • Tel: [phone] • 630-231-5900 • FAX: [phone] • www.nationalcontrols.com
1-16
Single Shot
Q2F Series
FEATURES
●
●
●
●
●
●
●
●
●
Operating Logic: Input voltage is applied to
the timer at all times. Upon a momentary or
maintained closure of a normally open iso-
lated start switch, the load energizes and
the time delay starts. At the end of the pre-
set time delay, the load de-energizes and
the timer is ready for a new timing cycle.
(Start switch supplied by customer)
Note: 1) Remote start switch leads should be shielded when run-
ning close to other wires; 2) Remote potentiometer leads should
be shielded when running close to other wires; 3) The minimum
time setting on external resistor-adjustable time delay relays is
obtained by shorting together the external resistor terminals of
the relay; 4) The maximum time setting within tolerance limits is
obtained by using a 1 megohm resistor; 5) Timing values between
the minimum and maximum limits are linear with resistance within
10%; 6) Recommend 1/4 W minimum resistor be used.
ORDERING INFORMATION
Optional Potentiometer: Part Number ASY-0001M-450
Consult factory for any special requirements not listed in catalog (minimum order requirement may apply).
Trigger time (start switch closure)
Reset time
Min. load
Max. leakage current
Voltage drop at 1 A
Power consumption
Peak 1 cycle surge
Protection
100% functionally tested
Solid state digital timing
Time delays to 10 hours standard
20:1 maximum to minimum timing ratio
Low cost
Compact size
Superior transient protection
Flame-retardant and solvent-resistant
polyester thermoplastic housing
180 to 3600 sec.
15 to 300 sec.
30 to 600 sec.
TIME RANGE
.05 to 1 sec.
.25 to 5 sec.
.5 to 10 sec.
3 to 60 sec.
TIME DELAY RELAYS
.25 to 5 hrs.
.5 to 10 hrs.
File #E65038
Q2F-00001-326
Q2F-00005-326
Q2F-00010-326
Q2F-00060-326
Q2F-00300-326
Q2F-00600-326
Q2F-03600-326
Q2F-18000-326
Q2F-36000-326
12 VDC +10%
8.8j. MOV
200 ms
20 ms
10 uA
2.6 W
5 mA
2.1 V
4 A
24 VAC/DC +10%
Q2F-00001-327
Q2F-00005-327
Q2F-00010-327
Q2F-00060-327
Q2F-00300-327
Q2F-00600-327
Q2F-03600-327
Q2F-18000-327
3.7 VA max.
8.8j. MOV
LOGIC FUNCTION DIAGRAM
Input
Voltage
Start
Switch
Load
SPECIFICATIONS
TIME DELAY
Adjustment: External resistor factory fixed on
special order (min. order requirement)
Range: 50 ms to 10 hours in 9 ranges
Repeatability: ±.5% +8 ms max. (0.25% typical)
at constant temperature
Accuracy:
Maximum time ±2% at Rt = 1 megohms
Minimum time +0%, -30% at Rt = 0 ohm
INPUT
Operating Voltage: 120, 240 VAC; 12 VDC; 24
VAC/DC ±10% (DC models have reverse polarity
protection; unfiltered input voltage to them must
be full-wave rectified)
Frequency: 50/60 Hz
OUTPUT
Type: Solid state, normally open
Rating: 1 A steady state
Life: 100,000,000 operations
PROTECTION
Transient Voltage: Metal oxide varistor, see rat-
ings below
Dielectric Breakdown: 3000 VAC, RMS, termi-
nals to mounting
300 ms
20 ms
10 uA
5 mA
3.2 V
4 A
—
Closed
Open
On
Off
On
Off
Q2F-00001-321
Q2F-00005-321
Q2F-00010-321
Q2F-00060-321
Q2F-00300-321
Q2F-00600-321
Q2F-03600-321
Q2F-18000-321
Q2F-36000-321
120 VAC +10%
4.3 VA max.
Single Shot Function
30j. MOV
300 ms
200 uA
20 ms
2 mA
3.3 V
20 A
Timing
Q2F-00001-325
Q2F-00005-325
Q2F-00010-325
Q2F-00060-325
Q2F-00600-325
Q2F-18000-325
240 VAC +10%
5.8 VA max.
30j. MOV
200 ms
300 uA
20 ms
2 mA
3.3 V
20 A
—
—
—
Insulation Resistance: 100 megohms
min. between terminals and case
MECHANICAL
Termination: .25” x .032” male fast-on
terminals
Mounting: Surface mount with one #8
screw
ENVIRONMENTAL
Storage Temperature: -40°C to 85°C
Operating Temperature: -40°C to 65°C
Humidity: 95% relative
External Resistance/Time Delay Relationship
1 megohm external resistance is required to obtain
the maximum time for all ranges. To determine the
actual resistance needed to obtain the required time
delay, use the following formula:
Note: Due to component tolerances, the actual time
obtained will normally be within 5% of desired time.
Rt=
START
SWITCH
Tmaximum - Tminimum
Trequired - Tminimum
Rt
(3667-4)
LOAD
5
1
.25 X .032 MALE FAST-ON
2.00 SQ.
TERMINALS (7 PL.)
Polarity Shown is
4
C L
2
for D.C. Models
VOLTAGE
1.25
INPUT
x 1,000,000 ohms
.88
3
L C
.170
DIA.