cp3bt13 National Semiconductor Corporation, cp3bt13 Datasheet - Page 103

• Manufacturer Part Number: cp3bt13
• Description: Cp3bt13 Reprogrammable Connectivity Processor With Bluetooth-r And Can Interfaces
• Manufacturer: National Semiconductor Corporation

16.10.9 Basic Mask Register (BMSKB/BMSKX)
The BMSKB and BMSKX registers allow masking the buffer
14, or “don’t care” the incoming extended/standard identifier
bits, RTR/XRTR, and IDE. Throughout this document, the
two 16-bit registers BMSKB and BMSKX are referenced to
as a 32-bit register BMSK.
The following are the bits for the BMSKB register.
The following are the bits for the BMSKX register.
For all BMSKB and BMSKX register bits the following ap-
plies:
0 – The incoming identifier bit must match the correspond-
1 – Accept 1 or 0 (“don’t care”) in the incoming ID bit inde-
When an extended frame is received from the CAN bus, all
BMSK bits BM[28:0], IDE, RTR, and XRTR are used to
mask the incoming message. In this case, the RTR bit in the
BMSK register corresponds to the SRR bit in the message.
The XRTR bit in the BMSK register corresponds to the RTR
bit in the message.
During the reception of standard frames, only the BMSK bits
BM[28:18], RTR, and IDE are used. In this case, the
BM[28:18] bits in the BMSK register correspond to the
ID[10:0] bits in the message.
15
Basic Mask BM[28:18]
Extended
Standard
Frame
Frame
pendent from the corresponding bit in the message
buffer ID registers. The corresponding ID bit in the mes-
sage buffer will be overwritten by the incoming identifier
bits.
15
ing bit in the message buffer identifier register.
BM[28:18]
ID[28:18]
ID[10:0]
BM[14:0]
5
R/W
R/W
0
0
SRR IDE
RTR IDE BM[17:0] XRTR
RTR IDE
RTR
4
IDE
3
ID[17:0]
2
BM[17:15]
1
Unused
XRTR
RTR
0
0
103
16.10.10 CAN Interrupt Enable Register (CIEN)
The CAN Interrupt Enable (CIEN) register enables the
transmit/receive interrupts of the message buffers 0 through
14 as well as the CAN Error Interrupt.
EIEN
IEN
16.10.11 CAN Interrupt Pending Register (CIPND)
The CIPND register indicates any CAN Receive/Transmit
Interrupt Requests caused by the message buffers 0..14
and CAN error occurrences.
EIPND
IPND
EIPND
EIEN
15
15
14
14
The Error Interrupt Enable bit allows the CAN
module to interrupt the CPU if any kind of
CAN receive/transmit errors are detected.
This causes any error status change in the er-
ror counter registers REC/TEC is able to gen-
erate an error interrupt.
0 – The error interrupt is disabled and no er-
1 – The error interrupt is enabled and a
The Buffer Interrupt Enable bits allow software
to enable/disable the interrupt source for the
corresponding message buffer. For example,
IEN14 controls interrupts from buffer14, and
IEN0 controls interrupts from buffer0.
0 – Buffer as interrupt source disabled.
1 – Buffer as interrupt source enabled.
The Error Interrupt Pending field indicates the
status change of TEC/REC and will execute
an error interrupt if the EIEN bit is set. Soft-
ware has the responsibility to clear the EIPND
bit using the CICLR register.
0 – CAN status is not changed.
1 – CAN status is changed.
The Buffer Interrupt Pending bits are set by
the CAN module following a successful trans-
mission or reception of a message to or from
the corresponding message buffer. For exam-
ple, IPND14 corresponds to buffer14, and
IPND0 corresponds to buffer0.
0 – No interrupt pending for the correspond-
1 – Message buffer has generated an inter-
ror interrupt will be generated.
change in REC/TEC will cause an inter-
rupt to be generated.
ing message buffer.
rupt.
R/W
R
0
0
IPND
IEN
www.national.com
0
0