cp3bt13 National Semiconductor Corporation, cp3bt13 Datasheet - Page 122

• Manufacturer Part Number: cp3bt13
• Description: Cp3bt13 Reprogrammable Connectivity Processor With Bluetooth-r And Can Interfaces
• Manufacturer: National Semiconductor Corporation

www.national.com
17.7.8
The ASCR register controls the basic operation of the inter-
face. It also holds bits which report the current status of the
audio communication. The CPU bus master has read/write
access to the ASCR register. At reset, this register is loaded
with F003h.
TXAE
TXE
TXF
TXU
TXSA
15
7
(ATSCR)
Audio Transmit Status and Control Register
TXFWL
TXSA
The Transmit FIFO Almost Empty bit is set
when the number of data bytes/words in
transmit buffer is equal to the specified warn-
ing limit.
0 – Transmit FIFO above warning limit.
1 – Transmit FIFO at or below warning limit.
The Transmit FIFO Empty bit is set when the
transmit buffer is empty. The TXE bit is set to
one every time the TRP is equal to the TWP
and the last access to the FIFO was read op-
eration (into ATSR).
0 – Transmit FIFO not empty.
1 – Transmit FIFO empty.
The Transmit FIFO Full bit is set when the
TWP is equal to the TRP and the last access
to the FIFO was write operation (write to AT-
DR).
0 – Transmit FIFO not full.
1 – Transmit FIFO full.
The Transmit Underflow bit indicates that the
transmit shift register (ATSR) has underrun.
This occurs when the transmit FIFO was al-
ready empty and a complete data word has
been transferred. In this case, the TRP will be
decremented by 1 and the previous data will
be retransmitted. No transmit interrupt and no
DMA request will be generated (even if en-
abled).
0 – Transmit underrun occurred.
1 – Transmit underrun did not occur.
The Transmit Slot Assignment field specifies
during which slots the transmitter is active and
drives data through the STD pin. The STD pin
is in high impedance state during all other
slots. If the frame consists of less than 4 slots,
the TXSA bits for unused slots are ignored.
For example, if a frame only consists of 2
slots, TXSA bits 2 and 3 are ignored. The fol-
lowing table shows the slot assignment
scheme.
12
4
TXU
11
3
TXF
2
TXDSA
TXE TXAE
1
0
8
122
TXDSA
TFWL
After reset, the TXSA field is clear, so soft-
ware must load the correct slot assignment.
The Transmit DMA Slot Assignment field
specifies which slots (audio channels) are
supported by DMA. If the TXDSA bit is set for
an assigned slot n (TXSAn = 1), the data to be
transmitted within this slot will not be read
from the transmit FIFO, but will instead be
read from the corresponding Transmit DMA
data register (ATDRn). A DMA request n is as-
serted when the ATDRn is empty. If the TSA
bit for a slot is clear, the TXDSA bit is ignored.
The following table shows the DMA slot as-
signment scheme.
The Transmit FIFO Warning Level field speci-
fies when a transmit interrupt is asserted. A
transmit interrupt is asserted when the num-
ber of bytes or words in the transmit FIFO is
equal or less than the warning level value. A
TXFWL value of Fh means that a transmit in-
terrupt is asserted if one or more bytes or
words are available in the transmit FIFO. At
reset, the TXFWL field is loaded with Fh.
TXDSA Bit
TXSA Bit
TXDSA0
TXDSA1
TXDSA2
TXDSA3
TXSA0
TXSA1
TXSA2
TXSA3
Slots Enabled
Slots Enabled
for DMA
0
1
2
3
0
1
2
3