ATA6613P-PLQW Atmel, ATA6613P-PLQW Datasheet - Page 102

• Manufacturer Part Number: ATA6613P-PLQW
• Description: MCU W/LIN TXRX REG WTCHDG 48-QFN
• Manufacturer: Atmel
• Series: AVR® ATA66 LIN-SBCr

Specifications of ATA6613P-PLQW

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-QFN Exposed Pad
• Processor Series: ATA6x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

102
Atmel ATA6612/ATA6613
• SDA/ADC4/PCINT12 – Port C, Bit 4
• ADC3/PCINT11 – Port C, Bit 3
• ADC2/PCINT10 – Port C, Bit 2
• ADC1/PCINT9 – Port C, Bit 1
• ADC0/PCINT8 – Port C, Bit 0
SDA, 2-wire Serial Interface Data: When the TWEN bit in TWCR is set (one) to enable the
2-wire Serial Interface, pin PC4 is disconnected from the port and becomes the Serial
Data I/O pin for the 2-wire Serial Interface. In this mode, there is a spike filter on the pin to
suppress spikes shorter than 50 ns on the input signal, and the pin is driven by an open
drain driver with slew-rate limitation.
PC4 can also be used as ADC input Channel 4. Note that ADC input channel 4 uses digi-
tal power.
PCINT12: Pin Change Interrupt source 12. The PC4 pin can serve as an external interrupt
source.
PC3 can also be used as ADC input Channel 3. Note that ADC input channel 3 uses ana-
log power.
PCINT11: Pin Change Interrupt source 11. The PC3 pin can serve as an external interrupt
source.
PC2 can also be used as ADC input Channel 2. Note that ADC input channel 2 uses ana-
log power.
PCINT10: Pin Change Interrupt source 10. The PC2 pin can serve as an external interrupt
source.
PC1 can also be used as ADC input Channel 1. Note that ADC input channel 1 uses ana-
log power.
PCINT9: Pin Change Interrupt source 9. The PC1 pin can serve as an external interrupt
source.
PC0 can also be used as ADC input Channel 0. Note that ADC input channel 0 uses ana-
log power.
PCINT8: Pin Change Interrupt source 8. The PC0 pin can serve as an external interrupt
source.
9111H–AUTO–01/11