UPD78F0513AMC-GAA-AX Renesas Electronics America, UPD78F0513AMC-GAA-AX Datasheet - Page 453

• Manufacturer Part Number: UPD78F0513AMC-GAA-AX
• Description: MCU 8BIT 38PIN SSOP
• Manufacturer: Renesas Electronics America
• Series: 78K0/Kx2r

Specifications of UPD78F0513AMC-GAA-AX

• Core Processor: 78K/0
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 31
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

78K0/Kx2
15.1 Functions of Serial Interface UART6
(1) Operation stop mode
(2) Asynchronous serial interface (UART) mode
R01UH0008EJ0401 Rev.4.01
Jul 15, 2010
Serial interface UART6 are mounted onto all 78K0/Kx2 microcontroller products.
Serial interface UART6 has the following two modes.
This mode is used when serial communication is not executed and can enable a reduction in the power consumption.
For details, see 15.4.1 Operation stop mode.
This mode supports the LIN (Local Interconnect Network)-bus. The functions of this mode are outlined below.
For details, see 15.4.2 Asynchronous serial interface (UART) mode and 15.4.3 Dedicated baud rate generator.
• Maximum transfer rate: 625 kbps
• Two-pin configuration
• Data length of communication data can be selected from 7 or 8 bits.
• Dedicated internal 8-bit baud rate generator allowing any baud rate to be set
• Transmission and reception can be performed independently (full duplex operation).
• MSB- or LSB-first communication selectable
• Inverted transmission operation
• Sync break field transmission from 13 to 20 bits
• More than 11 bits can be identified for sync break field reception (SBF reception flag provided).
Cautions 1. The T
2. If clock supply to serial interface UART6 is not stopped (e.g., in the HALT mode), normal
3. Set POWER6 = 1 and then set TXE6 = 1 (transmission) or RXE6 = 1 (reception) to start
4. TXE6 and RXE6 are synchronized by the base clock (f
5. Set transmit data to TXB6 at least one base clock (f
6. If data is continuously transmitted, the communication timing from the stop bit to the next start
side. To use this function, the reception side must be ready for reception of inverted data.
operation continues. If clock supply to serial interface UART6 is stopped (e.g., in the STOP
mode), each register stops operating, and holds the value immediately before clock supply was
stopped. The T
outputs it. However, the operation is not guaranteed after clock supply is resumed. Therefore,
reset the circuit so that POWER6 = 0, RXE6 = 0, and TXE6 = 0.
communication.
transmission or reception again, set TXE6 or RXE6 to 1 at least two clocks of the base clock
after TXE6 or RXE6 has been cleared to 0. If TXE6 or RXE6 is set within two clocks of the base
clock, the transmission circuit or reception circuit may not be initialized.
bit is extended two operating clocks of the macro. However, this does not affect the result of
communication because the reception side initializes the timing when it has detected a start bit.
Do not use the continuous transmission function if the interface is used in LIN communication
operation.
X
D6 output inversion function inverts only the transmission side and not the reception
T
R
X
X
D6: Transmit data output pin
D6: Receive data input pin
CHAPTER 15 SERIAL INTERFACE UART6
X
D6 pin also holds the value immediately before clock supply was stopped and
CHAPTER 15 SERIAL INTERFACE UART6
XCLK6
) after setting TXE6 = 1.
XCLK6
) set by CKSR6.
To enable
453