82P2284BB IDT, Integrated Device Technology Inc, 82P2284BB Datasheet - Page 17

• Manufacturer Part Number: 82P2284BB
• Manufacturer: IDT, Integrated Device Technology Inc

Specifications of 82P2284BB

• Screening Level: Industrial
• Mounting: Surface Mount
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Lead Free Status / RoHS Status: Not Compliant

Note:
* This feature is available in ZB revision only.
Pin Description
IDT82P2284
CLK_GEN_1.544
CLK_GEN_2.048
CLK_SEL[0]
CLK_SEL[1]
CLK_SEL[2]
REFA_OUT
REFB_OUT
GPIO[0]
GPIO[1]
RESET
OSCO
Name
OSCI
THZ
Output / Input
Output
Output
Output
Output
Output
Type
Input
Input
Input
Input
Pin No.
B13
C13
D15
C14
B15
A16
D14
A15
B14
A14
E13
D13
B16
OSCI: Crystal Oscillator Input
This pin is connected to an external clock source. In T1 mode E1 Rate of Transmit System interface, this
clock must keep the source same with system transmit clock (TSCKn/MTSCK).
The clock frequency of OSCI is defined by CLK_SEL[2:0]. The clock accuracy should be ±32 ppm and duty
cycle should be from 40% to 60%.
OSCO: Crystal Oscillator Output
This pin outputs the inverted, buffered clock input from OSCI.
CLK_SEL[2:0]: Clock Selection
These three pins select the input clock signal:
When the CLK_SEL[2] pin is low, the input clock signal is N X 1.544 MHz;
When the CLK_SEL[2] pin is high, the input clock signal is N X 2.048 MHz.
When the CLK_SEL[1:0] pins are ‘00’, the N is 1;
When the CLK_SEL[1:0] pins are ‘01’, the N is 2;
When the CLK_SEL[1:0] pins are ‘10’, the N is 3;
When the CLK_SEL[1:0] pins are ‘11’, the N is 4.
CLK_SEL[2:0] are Schmitt-trigger inputs.
CLK_GEN_1.544: Clock Generator 1.544 MHz Output
This pin outputs the 1.544 MHz clock signal generated by the Clock Generator.
CLK_GEN_2.048: Clock Generator 2.048 MHz Output
This pin outputs the 2.048 MHz clock signal generated by the Clock Generator.
REFA_OUT: Reference Clock Output A
The frequecy is 2.048 MHz (E1) or 1.544 MHz (T1/J1)
When no LOS is detected, this pin outputs a recovered clock from the Clock and Data Recovery function
block of one of the four links. The link is selected by the RO1[1:0] bits (b1~0, T1/J1-007H / b1~0, E1-007H).
When LOS is detected, this pin outputs MCLK or high level, as selected by the REFH_LOS bit (b0, T1/J1-
03EH,... / b0, E1-03EH,...). *
Note: MCLK is a clock derived from OSCI using an internal PLL, and the frequency is 2.048 MHz(E1) or 1.544
MHz(T1/J1).
REFB_OUT: Reference Clock Output B
The frequecy is 2.048 MHz(E1) or 1.544 MHz(T1/J1).
When no LOS is detected, this pin outputs a recovered clock from the Clock and Data Recovery function
block of one of the four links. The link is selected by the RO2[1:0] bits (b4~3, T1/J1-007H / b4~3, E1-007H).
When LOS is detected, this pin outputs MCLK or high level, as selected by the REFH_LOS bit (b0, T1/J1-
03EH,... / b0, E1-03EH,...). *
RESET: Reset (Active Low)
A low pulse for more than 100 ns on this pin resets the device. All the registers are accessible 2 ms after the
reset. The RESET pin is a Schmitt-trigger input with a weak pull-up resistor. The OSCI clock must exist when
the device be reset.
General Purpose I/O [1:0]
These two pins can be defined as input pins or output pins by the DIR[1:0] bits (b1~0, T1/J1-006H / b1~0, E1-
006H) respectively. When the pins are input, their polarities are indicated by the LEVEL[1:0] bits (b3~2, T1/J1-
006H / b3~2, E1-006H) respectively. When the pins are output, their polarities are controlled by the
LEVEL[1:0] bits (b3~2, T1/J1-006H / b3~2, E1-006H) respectively.
GPIO[1:0] are Schmitt-trigger input/output with a pull-up resistor.
THZ: Transmit High-Z
A high level on this pin puts all the TTIPn/TRINGn pins into high impedance state.
THZ is a Schmitt-trigger input.
Control Interface
Clock Generator
17
QUAD T1/E1/J1 LONG HAUL / SHORT HAUL TRANSCEIVER
Description
February 25, 2008