82P2284BB IDT, Integrated Device Technology Inc, 82P2284BB Datasheet - Page 18

• Manufacturer Part Number: 82P2284BB
• Manufacturer: IDT, Integrated Device Technology Inc

Specifications of 82P2284BB

• Screening Level: Industrial
• Mounting: Surface Mount
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Lead Free Status / RoHS Status: Not Compliant

Pin Description
IDT82P2284
DS / RD / SCLK
RW / WR / SDI
D[0] / SDO
Name
REFR
MPM
A[0]
A[1]
A[2]
A[3]
A[4]
A[5]
A[6]
A[7]
A[8]
A[9]
D[1]
D[2]
D[3]
D[4]
D[5]
D[6]
D[7]
INT
CS
Output / Input
Output
Output
Type
Input
Input
Input
Input
Input
Pin No.
C16
N10
P10
R10
T11
T10
P11
R5
N6
R6
N7
R7
N9
R9
R8
T5
P6
T6
P7
T7
P9
T9
T8
P8
INT: Interrupt (Active Low)
This is the open drain, active low interrupt output. This pin will stay low until all the active unmasked interrupt
indication bits are cleared.
REFR:
This pin should be connected to ground via an external 10K resistor.
CS: Chip Select (Active Low)
This pin must be asserted low to enable the microprocessor interface. The signal must be asserted high at
least once after power up to clear the internal test modes. A transition from high to low must occur on this pin
for each Read/Write operation and can not return to high until the operation is completed.
CS is a Schmitt-trigger input.
A[9:0]: Address Bus
In parallel mode, the signals on these pins select the register for the microprocessor to access.
In SPI mode, these pins should be connected to ground.
A[9:0] are Schmitt-trigger inputs.
D[7:0]: Bi-directional Data Bus
In parallel mode, the signals on these pins are the data for Read / Write operation.
In SPI mode, the D[7:1] pins should be connected to the ground through a 10 K resistor.
D[7:0] are Schmitt-trigger inputs/outputs.
SDO: Serial Data Output
In SPI mode, the data is serially output on this pin.
MPM: Micro Controller Mode
In parallel mode, set this pin low for Motorola mode or high for Intel mode.
In SPI mode, set this pin to a fixed level (high or low). This pin is useless in SPI mode.
MPM is a Schmitt-trigger input.
RW: Read / Write Select
In parallel Motorola mode, this pin is active high for read operation and active low for write operation.
WR: Write Strobe (Active Low)
In parallel Intel mode, this pin is active low for write operation.
SDI: Serial Data Input
In SPI mode, the address/control and/or data are serially input on this pin.
RW / WR / SDI is a Schmitt-trigger input.
DS: Data Strobe (Active Low)
In parallel Motorola mode, this pin is active low.
RD: Read Strobe (Active Low)
In parallel Intel mode, this pin is active low for read operation.
SCLK: Serial Clock
In SPI mode, this pin inputs the timing for the SDO and SDI pins. The signal on the SDO pin is updated on the
falling edge of SCLK, while the signal on the SDI pin is sampled on the rising edge of SCLK.
DS / RD / SCLK is a Schmitt-trigger input.
18
QUAD T1/E1/J1 LONG HAUL / SHORT HAUL TRANSCEIVER
Description
February 25, 2008