PIC24FJ64GB002-I/SS Microchip Technology, PIC24FJ64GB002-I/SS Datasheet - Page 210

• Manufacturer Part Number: PIC24FJ64GB002-I/SS
• Description: 16-bit, 16 MIPS, 64KB Flash, 8KB RAM, Nanowatt XLP, USB OTG 28 SSOP .209in TUBE
• Manufacturer: Microchip Technology

Specifications of PIC24FJ64GB002-I/SS

• Processor Series: PIC24
• Core: PIC24F
• Data Bus Width: 16 bit
• Program Memory Type: Flash
• Program Memory Size: 64 KB
• Data Ram Size: 8192 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 5
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: SSOP-28
• Development Tools By Supplier: MPLAB Integrated Development Environment
• Minimum Operating Temperature: - 40 C
• Operating Temperature Range: - 40 C to + 85 C
• Supply Current (max): 300 mA
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC24FJ64GB004 FAMILY
18.5.3
1.
2.
3.
4.
5.
6.
7.
DS39940D-page 210
Note:
Follow the procedure described in Section 18.5.1
“Enable Host Mode and Discover a Connected
Device” and Section 18.5.2 “Complete a Con-
trol Transaction to a Connected Device” to
discover and configure a device.
To enable transmit and receive transfers with
handshaking enabled, write 1Dh to U1EP0. If
the target device is a low-speed device, also set
the LSPD bit (U1EP0<7>). If you want the hard-
ware to automatically retry indefinitely if the
target device asserts a NAK on the transfer,
clear
(U1EP0<6>).
Set up the BD for the current (EVEN or ODD) Tx
EP0 to transfer up to 64 bytes.
Set the USB device address of the target device
in the address register (U1ADDR<6:0>).
Write an OUT token to the desired endpoint to
U1TOK. This triggers the module’s transmit
state machines to begin transmitting the token
and the data.
Wait for the Transfer Done Interrupt Flag,
TRNIF. This indicates that the BD has been
released back to the microprocessor, and the
transfer has completed. If the retry disable bit is
set, the handshake (ACK, NAK, STALL or
ERROR (0Fh)) is returned in the BD PID field. If
a STALL interrupt occurs, the pending packet
must be dequeued and the error condition in the
target device cleared. If a detach interrupt
occurs (SE0 for more than 2.5 s), then the
target has detached (U1IR<0> is set).
Once the transfer done interrupt occurs (TRNIF
is set), the BD can be examined and the next
data packet queued by returning to step 2.
SEND A FULL-SPEED BULK DATA
TRANSFER TO A TARGET DEVICE
the
USB speed, transceiver and pull-ups
should only be configured during the
module setup phase. It is not recom-
mended to change these settings while
the module is enabled.
Retry
Disable
bit,
RETRYDIS
18.6
18.6.1
An OTG A-device may decide to power down the V
supply when it is not using the USB link through the Ses-
sion Request Protocol (SRP). Software may do this by
clearing VBUSON (U1OTGCON<3>). When the V
supply is powered down, the A-device is said to have
ended a USB session.
An OTG A-device or Embedded Host may re-power the
V
OTG B-device may also request that the OTG A-device
re-power the V
is accomplished via Session Request Protocol (SRP).
Prior to requesting a new session, the B-device must
first check that the previous session has definitely
ended. To do this, the B-device must check for two
conditions:
1. V
2. Both D+ and D- have been low for at least 2 ms.
The B-device will be notified of condition 1 by the
SESENDIF (U1OTGIR<2>) interrupt. Software will
have to manually check for condition 2.
The B-device may aid in achieving condition 1 by dis-
charging the V
may do this by setting VBUSDIS (U1OTGCON<0>).
After these initial conditions are met, the B-device may
begin requesting the new session. The B-device begins
by pulsing the D+ data line. Software should do this by
setting DPPULUP (U1OTGCON<7>). The data line
should be held high for 5 to 10 ms.
BUS
Note:
BUS
supply at any time (initiate a new session). An
supply is below the Session Valid voltage, and
OTG Operation
SESSION REQUEST PROTOCOL
(SRP)
When the A-device powers down the V
supply, the B-device must disconnect its
pull-up resistor from power. If the device is
self-powered, it can do this by clearing
DPPULUP
DMPULUP (U1OTGCON<6>).
BUS
BUS
supply (initiate a new session). This
supply through a resistor. Software
 2010 Microchip Technology Inc.
(U1OTGCON<7>)
BUS
and
BUS
BUS