PIC24FJ64GB002-I/SS Microchip Technology, PIC24FJ64GB002-I/SS Datasheet - Page 277

• Manufacturer Part Number: PIC24FJ64GB002-I/SS
• Description: 16-bit, 16 MIPS, 64KB Flash, 8KB RAM, Nanowatt XLP, USB OTG 28 SSOP .209in TUBE
• Manufacturer: Microchip Technology

Specifications of PIC24FJ64GB002-I/SS

• Processor Series: PIC24
• Core: PIC24F
• Data Bus Width: 16 bit
• Program Memory Type: Flash
• Program Memory Size: 64 KB
• Data Ram Size: 8192 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 5
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: SSOP-28
• Development Tools By Supplier: MPLAB Integrated Development Environment
• Minimum Operating Temperature: - 40 C
• Operating Temperature Range: - 40 C to + 85 C
• Supply Current (max): 300 mA
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

REGISTER 25-1:
 2010 Microchip Technology Inc.
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7
bit 6-5
bit 4
Note 1:
EDG2POL
CTMUEN
R/W-0
R/W-0
If TGEN = 1, the peripheral inputs and outputs must be configured to an available RPn pin. For more
information, see Section 10.4 “Peripheral Pin Select (PPS)”.
CTMUEN: CTMU Enable bit
1 = Module is enabled
0 = Module is disabled
Unimplemented: Read as ‘0’
CTMUSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
TGEN: Time Generation Enable bit
1 = Enables edge delay generation
0 = Disables edge delay generation
EDGEN: Edge Enable bit
1 = Edges are not blocked
0 = Edges are blocked
EDGSEQEN: Edge Sequence Enable bit
1 = Edge 1 event must occur before Edge 2 event can occur
0 = No edge sequence is needed
IDISSEN: Analog Current Source Control bit
1 = Analog current source output is grounded
0 = Analog current source output is not grounded
CTTRIG: Trigger Control bit
1 = Trigger output is enabled
0 = Trigger output is disabled
EDG2POL: Edge 2 Polarity Select bit
1 = Edge 2 programmed for a positive edge response
0 = Edge 2 programmed for a negative edge response
EDG2SEL<1:0>: Edge 2 Source Select bits
11 = CTED1 pin
10 = CTED2 pin
01 = OC1 module
00 = Timer1 module
EDG1POL: Edge 1 Polarity Select bit
1 = Edge 1 programmed for a positive edge response
0 = Edge 1 programmed for a negative edge response
EDG2SEL1
R/W-0
U-0
—
CTMUCON: CTMU CONTROL REGISTER
W = Writable bit
‘1’ = Bit is set
CTMUSIDL
EDG2SEL0
R/W-0
R/W-0
EDG1POL
TGEN
R/W-0
R/W-0
PIC24FJ64GB004 FAMILY
(1)
(1)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
EDG1SEL1
EDGEN
R/W-0
R/W-0
EDGSEQEN
EDG1SEL0
R/W-0
R/W-0
x = Bit is unknown
EDG2STAT
IDISSEN
R/W-0
R/W-0
DS39940D-page 277
EDG1STAT
CTTRIG
R/W-0
R/W-0
bit 8
bit 0