MC9S12XDP512CAL Freescale, MC9S12XDP512CAL Datasheet - Page 714

• Manufacturer Part Number: MC9S12XDP512CAL
• Manufacturer: Freescale

Specifications of MC9S12XDP512CAL

• Cpu Family: HCS12
• Device Core Size: 16b
• Frequency (max): 40MHz
• Interface Type: CAN/I2C/SCI/SPI
• Total Internal Ram Size: 32KB
• # I/os (max): 91
• Number Of Timers - General Purpose: 12
• Operating Supply Voltage (typ): 2.5/5V
• Operating Supply Voltage (max): 2.75/5.5V
• Operating Supply Voltage (min): 2.35/3.15V
• On-chip Adc: 2(16-chx10-bit)
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 112
• Package Type: LQFP
• Program Memory Type: Flash
• Program Memory Size: 512KB
• Lead Free Status / RoHS Status: Compliant

Chapter 19 S12X Debug (S12XDBGV2) Module
If the TAG bit is clear (forced type trigger) a comparator match is generated when the selected address
appears on the system address bus. If the selected address is an opcode address, the match is generated
when the opcode is fetched from the memory. This precedes the instruction execution by an indefinite
number of cycles due to instruction pipe lining. For a comparator match of an opcode at an odd address
when TAG = 0, the corresponding even address must be contained in the comparator register. Thus for an
opcode at odd address (n), the comparator register must contain address (n – 1).
Once a successful comparator match has occurred, the condition that caused the original match is not
verified again on subsequent matches. Thus if a particular data value is verified at a given address, this
address may not still contain that data value when a subsequent match occurs.
Comparators C and D can also be used to select an address range to trace from. This is determined by the
TRANGE bits in the DBGTCR register. The TRANGE encoding is shown in
bits select a range definition using comparator D, then comparator D is configured for trace range
definition and cannot be used for address bus comparisons. Similarly if the TRANGE bits select a range
definition using comparator C, then comparator C is configured for trace range definition and cannot be
used for address bus comparisons.
Match[0,1,2,3] map directly to comparators [A,B,C,D] respectively, except in range modes (see
Section 19.3.1.4, “Debug Control Register2
trigger priority (see
19.4.2.1
With range comparisons disabled, the match condition is an exact equivalence of address/data bus with the
value stored in the comparator address/data registers. Further qualification of the type of access (R/W,
word/byte) is possible.
Comparators A and C do not feature SZE or SZ control bits, thus the access size is not compared. The exact
address is compared, thus with the comparator address register loaded with address (n) a misaligned word
access of address (n-1) also accesses (n) but does not cause a match
without data bus compare.
byte accesses DBGXDH must be loaded with the data byte. The low byte must be masked out using the
DBGXDLM mask register. On word accesses data byte of the lower address is mapped to DBGXDH.
Comparators A and C feature an NDB control bit to determine if a match occurs when the data bus differs
to comparator register contents or when the data bus is equivalent to the comparator register contents.
716
Access
Word
Word
Word
Byte
Address
ADDR[n]
ADDR[n]
ADDR[n]
ADDR[n]
Exact Address Comparator Match (Comparators A and C)
Section 19.4.3.6, “Trigger
Table 19-36. Comparator A and C Data Bus Considerations
DBGxDH
Data[n]
Data[n]
Data[n]
Table 19-36
x
MC9S12XDP512 Data Sheet, Rev. 2.21
Data[n+1]
Data[n+1]
DBGxDL
lists access considerations with data bus comparison. To compare
x
x
(DBGC2)”). Comparator priority rules are described in the
Priorities”).
DBGxDHM
0x_FF
0x_FF
0x_FF
0x_00
DBGxDLM
0x_FF
0x_FF
0x_00
0x_00
Table 19-37
Table
lists access considerations
MOVW #$WORD ADDR[n]
MOVW #$WORD ADDR[n]
MOVW #$WORD ADDR[n]
MOVB #$BYTE ADDR[n]
Example Valid Match
19-10. If the TRANGE
Freescale Semiconductor