AT32UC3C0256C Atmel Corporation, AT32UC3C0256C Datasheet - Page 1229

• Manufacturer Part Number: AT32UC3C0256C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C0256C

• Flash (kbytes): 256 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 123
• Ext Interrupts: 144
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 20
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

39.6
39.6.1
39.6.2
32117C–AVR-08/11
aWire Debug Interface (AW)
Features
Overview
Rev.: 2.3.0.1
•
•
•
•
•
•
•
•
The aWire Debug Interface (AW) offers a single pin debug solution that is fully compatible with
the functionality offered by the JTAG interface, except boundary scan. This functionality includes
memory access, programming capabilities, and On-Chip Debug access.
Figure 39-8 on page 1230
RESET_N pin is used both as reset and debug pin. A special sequence on RESET_N is needed
to block the normal reset functionality and enable the AW.
The Service Access Bus (SAB) interface contains address and data registers for the Service
Access Bus, which gives access to On-Chip Debug, programming, and other functions in the
device. The SAB offers several modes of access to the address and data registers, as dis-
cussed in
Section 39.6.7
description in this document.
If the AW is not used for debugging, the aWire UART can be used by the user to send or receive
data with one stop bit, eight data bits, no parity bits, and one stop bit. This can be controlled
through the aWire user interface.
Single pin debug system.
Half Duplex asynchronous communication (UART compatible).
Full duplex mode for direct UART connection.
Compatible with JTAG functionality, except boundary scan.
Failsafe packet-oriented protocol.
Read and write on-chip memory and program on-chip flash and fuses through SAB interface.
On-Chip Debug access through SAB interface.
Asynchronous receiver or transmitter when the aWire system is not used for debugging.
Section
lists the supported aWire commands and responses, with references to the
39.6.6.8.
shows how the AW is connected in a 32-bit AVR device. The
AT32UC3C
1229