AT32UC3C0256C Atmel Corporation, AT32UC3C0256C Datasheet - Page 971

• Manufacturer Part Number: AT32UC3C0256C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C0256C

• Flash (kbytes): 256 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 123
• Ext Interrupts: 144
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 20
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Figure 33-4. Non Overlapped Center Aligned Waveforms
32117C–AVR-08/11
OC0
OC1
Note:
When center aligned, the channel counter increases up to CPRD and decreases down to 0. This
ends the period.
When left aligned, the channel counter increases up to CPRD and is reset. This ends the period.
Thus, for the same CPRD value, the period for a center aligned channel is twice the period for a
left aligned channel.
Waveforms are fixed at 0 when:
Waveforms are fixed at 1 (once the channel is enabled) when:
The waveform polarity must be written before enabling the channel. This immediately affects the
channel output level. Changes on channel polarity are not taken into account while the channel
is enabled.
Besides generating output signals OCx, the comparator generates interrupts in function of the
counter value. When the output waveform is left aligned, the interrupt occurs at the end of the
counter period. When the output waveform is center aligned, the CES bit of the CMRx register
defines when the channel counter interrupt occurs. If CES is set to 0, the interrupt occurs at the
end of the counter period. If CES is set to 1, the interrupt occurs at the end of the counter period
and at half of the counter period.
Figure 33-5 on page 972
• the waveform polarity. At the beginning of the period, the signal can be at high or low level.
• the waveform alignment. The output waveform can be left or center aligned. Center aligned
• CDTY = CPRD and CPOL = 0
• CDTY = 0 and CPOL = 1
• CDTY = 0 and CPOL = 0
• CDTY = CPRD and CPOL = 1
This property is defined in the CPOL field of the CMRx register. By default the signal starts by
a low level.
waveforms can be used to generate non overlapped waveforms. This property is defined in
the CALG field of the CMRx register. The default mode is left aligned.
No overlap
1. See
Period
Figure 33-5 on page 972
illustrates the counter interrupts in function of the configuration.
for a detailed description of center aligned waveforms.
AT32UC3C
971