AT32UC3C0256C Atmel Corporation, AT32UC3C0256C Datasheet - Page 604

• Manufacturer Part Number: AT32UC3C0256C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C0256C

• Flash (kbytes): 256 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 123
• Ext Interrupts: 144
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 20
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

25.6.9.7
Figure 25-40. Header Reception
25.6.9.8
32117C–AVR-08/11
With RSTSTA=1
Write US_CR
Baud Rate
US_LINIR
Clock
LINID
RXD
Header Reception (Slave Node Configuration)
Slave Node Synchronization
All the LIN Frames start with a header which is sent by the master node and consists of a Synch
Break Field, Synch Field and Identifier Field.
In Slave node configuration, the frame handling starts with the reception of the header.
The USART uses a break detection threshold of 11 nominal bit times at the actual baud rate. At
any time, if 11 consecutive recessive bits are detected on the bus, the USART detects a Break
Field. As long as a Break Field has not been detected, the USART stays idle and the received
data are not taken in account.
When a Break Field has been detected, the USART expects the Synch Field character to be
0x55. This field is used to update the actual baud rate in order to stay synchronized (see
25.6.9.8). If the received Synch character is not 0x55, an Inconsistent Synch Field error is gen-
erated (see
After receiving the Synch Field, the USART expects to receive the Identifier Field.
When the Identifier has been received, the flag LINID is set to “1”. At this moment the field
IDCHR in the LIN Identifier register (LINIR) is updated with the received character. The Identifier
parity bits can be automatically computed and checked (see
If the header is not entirely received within the time given by the maximum length of the header
THeader_Maximum, the error bit LINHTE in the Channel Status register (CSR) is set to 1.
The bits LINID, LINBK and LINHTE are reset by writing the bit RSTSTA to 1 in the Control regis-
ter (CR).
The synchronization is done only in Slave node configuration. The procedure is based on time
measurement between falling edges of the Synch Field. The falling edges are available in dis-
tances of 2, 4, 6 and 8 bit times.
Figure 25-41. Synch Field
13 dominant bits (at 0)
Break Field
Section
1 recessive bit
25.6.10).
Start
Delimiter
Break
bit
(at 1)
2 Tbit
Start
Bit
1
2 Tbit
0
Synch Byte = 0x55
1
8 Tbit
0
Synch Field
1
0
2 Tbit
1
0
Stop
Bit
Start
Bit
2 Tbit
ID0 ID1 ID2
Section
ID3
25.6.9.9).
ID4
Stop
bit
ID5
AT32UC3C
ID6
ID7
Stop
Bit
Section
604