AT32UC3C0256C Atmel Corporation, AT32UC3C0256C Datasheet - Page 566

• Manufacturer Part Number: AT32UC3C0256C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C0256C

• Flash (kbytes): 256 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 123
• Ext Interrupts: 144
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 20
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

25.6
32117C–AVR-08/11
Functional Description
The USART is capable of managing several types of serial synchronous or asynchronous
communications.
It supports the following communication modes:
•
•
• 5- to 9-bit full-duplex asynchronous serial communication
• High-speed 5- to 9-bit full-duplex synchronous serial communication
• RS485 with driver control signal
• ISO7816, T0 or T1 protocols for interfacing with smart cards
• InfraRed IrDA Modulation and Demodulation
SPI Mode
LIN Mode
– Master or Slave
– Serial Clock Programmable Phase and Polarity
– SPI Serial Clock (CLK) Frequency up to Internal Clock Frequency CLK_USART/4
– Compliant with LIN 1.3 and LIN 2.0 specifications
– Master or Slave
– Processing of frames with up to 256 data bytes
– Response Data length can be configurable or defined automatically by the Identifier
– Self synchronization in Slave node configuration
– Automatic processing and verification of the “Synch Break” and the “Synch Field”
– The “Synch Break” is detected even if it is partially superimposed with a data byte
– Automatic Identifier parity calculation/sending and verification
– Parity sending and verification can be disabled
– Automatic Checksum calculation/sending and verification
– Checksum sending and verification can be disabled
– Support both “Classic” and “Enhanced” checksum types
– MSB- or LSB-first
– 1, 1.5 or 2 stop bits
– Parity even, odd, marked, space or none
– By 8 or by 16 over-sampling receiver frequency
– Optional hardware handshaking
– Optional modem signals management
– Optional break management
– Optional multidrop serial communication
– MSB- or LSB-first
– 1 or 2 stop bits
– Parity even, odd, marked, space or none
– By 8 or by 16 over-sampling frequency
– Optional hardware handshaking
– Optional modem signals management
– Optional break management
– Optional multidrop serial communication
– NACK handling, error counter with repetition and iteration limit, inverted data
AT32UC3C
566