AT32UC3C0256C Atmel Corporation, AT32UC3C0256C Datasheet - Page 50

• Manufacturer Part Number: AT32UC3C0256C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C0256C

• Flash (kbytes): 256 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 123
• Ext Interrupts: 144
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 68
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 20
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

7. Power Manager (PM)
7.1
7.2
32117C–AVR-08/11
Features
Overview
Rev: 4.1.2.3
•
•
•
•
•
•
The Power Manager (PM) provides synchronous clocks used to clock the main digital logic in the
device, namely the CPU, and the modules and peripherals connected to the High Speed Bus
(HSB) and the Peripheral Buses (PBx).
The PM also contains advanced power-saving features, allowing the user to optimize the power
consumption for an application. The synchronous clocks are divided into a number of clock
domains, one for the CPU and HSB and one for each PBx. The clocks can run at different
speeds, so the user can save power by running peripherals at a relatively low clock, while main-
taining a high CPU performance. Additionally, the clocks can be independently changed on-the-
fly, without halting any peripherals. This enables the user to adjust the speed of the CPU and
memories to the dynamic load of the application, without disturbing or re-configuring active
peripherals.
Each module also has a separate clock, enabling the user to switch off the clock for inactive
modules, to save further power. Additionally, clocks and oscillators can be automatically
switched off during idle periods by using the sleep instruction on the CPU. The system will return
to normal operation on occurrence of interrupts.
The Power Manager also contains a Reset Controller, which collects all possible reset sources,
generates hard and soft resets, and allows the reset source to be identified by software.
Generates clocks and resets for digital logic
On-the-fly frequency change of CPU, HSB and PBx clocks
Sleep modes allow simple disabling of logic clocks and clock sources
Module-level clock gating through maskable peripheral clocks
Wake-up from internal or external interrupts
Automatic identification of reset sources
AT32UC3C
50