S9S12P32J0VFTR Freescale Semiconductor, S9S12P32J0VFTR Datasheet - Page 218

• Manufacturer Part Number: S9S12P32J0VFTR
• Description: 16-bit Microcontrollers - MCU 16 BIT 32K FLASH
• Manufacturer: Freescale Semiconductor

Specifications of S9S12P32J0VFTR

• Rohs: yes
• Core: S12
• Processor Series: MC9S12P
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 16 MHz
• Program Memory Size: 32 KB
• Data Ram Size: 2 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 3.15 V to 5.5 V
• Operating Temperature Range: - 40 C to + 105 C
• Package / Case: QFN-48
• Mounting Style: SMD/SMT

S12 Clock, Reset and Power Management Unit (S12CPMU)
218
WRTMASK
RSBCK
CR[2:0]
WCOP
Field
2–0
7
6
5
Window COP Mode Bit — When set, a write to the CPMUARMCOP register must occur in the last 25% of the
selected period. A write during the first 75% of the selected period generates a COP reset. As long as all writes
occur during this window, $55 can be written as often as desired. Once $AA is written after the $55, the time-out
logic restarts and the user must wait until the next window before writing to CPMUARMCOP.
the duration of this window for the seven available COP rates.
0 Normal COP operation
1 Window COP operation
COP and RTI Stop in Active BDM Mode Bit
0 Allows the COP and RTI to keep running in Active BDM mode.
1 Stops the COP and RTI counters whenever the part is in Active BDM mode.
Write Mask for WCOP and CR[2:0] Bit — This write-only bit serves as a mask for the WCOP and CR[2:0] bits
while writing the CPMUCOP register. It is intended for BDM writing the RSBCK without changing the content of
WCOP and CR[2:0].
0 Write of WCOP and CR[2:0] has an effect with this write of CPMUCOP
1 Write of WCOP and CR[2:0] has no effect with this write of CPMUCOP.
COP Watchdog Timer Rate Select — These bits select the COP time-out rate (see
nonzero value to CR[2:0] enables the COP counter and starts the time-out period. A COP counter time-out
causes a System Reset. This can be avoided by periodically (before time-out) initializing the COP counter via
the CPMUARMCOP register.
While all of the following four conditions are true the CR[2:0], WCOP bits are ignored and the COP operates at
highest time-out period (
(Does not count for “write once”.)
1) COP is enabled (CR[2:0] is not 000)
2) BDM mode active
3) RSBCK = 0
4) Operation in special mode
CR2
0
0
0
0
1
1
1
1
Table 7-11. CPMUCOP Field Descriptions
2
S12P-Family Reference Manual, Rev. 1.13
24
CR1
Table 7-12. COP Watchdog Rates
cycles) in normal COP mode (Window COP mode disabled):
0
0
1
1
0
0
1
1
CR0
0
1
0
1
0
1
0
1
Description
(COPCLK is either IRCCLK or
OSCCLK depending on the
Cycles to time-out
COPOSCSEL bit)
COP disabled
COPCLK
2
2
2
2
2
2
2
14
16
18
20
22
23
24
Table
Freescale Semiconductor
7-12). Writing a
Table 7-12
shows