DS3184DK Maxim Integrated Products, DS3184DK Datasheet - Page 278

• Manufacturer Part Number: DS3184DK
• Description: KIT DEMO FOR DS3184
• Manufacturer: Maxim Integrated Products

Specifications of DS3184DK

• Main Purpose: Telecom, ATM / Packet PHYs
• Utilized Ic / Part: DS3184
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Secondary Attributes: -
• Embedded: -
• Primary Attributes: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Register Name:
Register Description:
Register Address:
Bit #
Name
Default
Bit #
Name
Default
Bit 11: Continuous C-bit Parity Error Insertion Enable (CCPEIE) – When 0, single C-bit parity error insertion is
enabled. When 1, continuous C-bit parity error insertion is enabled, and C-bit parity errors will be transmitted
continuously if CPEI is high.
Bit 10: C-bit Parity Error Insertion Enable (CPEI) – When 0, C-bit parity error insertion is disabled. When 1, C-bit
parity error insertion is enabled.
Bit 9: Continuous Far-End Block Error Insertion Enable (CFBEIE) – When 0, single far-end block error
insertion is enabled. When 1, continuous far-end block error insertion is enabled, and far-end block errors will be
transmitted continuously if FBEI is high.
Bit 8: Far-End Block Error Insertion Enable (FBEI) – When 0, far-end block error insertion is disabled. When 1,
far-end block error insertion is enabled.
Bit 6: Continuous P-bit Parity Error Insertion Enable (CPEIE) – When 0, single P-bit parity error insertion is
enabled. When 1, continuous P-bit parity error insertion is enabled, and P-bit parity errors will be transmitted
continuously if PEI is high.
Bit 5: P-bit Parity Error Insertion Enable (PEI) – When 0, P-bit parity error insertion is disabled. When 1, P-bit
parity error insertion is enabled.
Bits 4 to 3: Framing Error Insertion Control (FEIC[1:0]) – These two bits control the framing error event to be
inserted.
Bit 2: Framing Error Insertion Enable (FEI) – When 0, framing error insertion is disabled. When 1, framing error
insertion is enabled.
Bit 1: Transmit Single Error Insert (TSEI) – This bit causes an error of the enabled type(s) to be inserted in the
transmit data stream if manual error insertion is disabled (MEIMS = 0). A 0 to 1 transition causes a single error to
be inserted. For a second error to be inserted, this bit must be set to 0, and back to 1. Note: If MEIMS is low, and
this bit transitions more than once between error insertion opportunities, only one error will be inserted.
Bit 0: Manual Error Insert Mode Select (MEIMS) – When 0, error insertion is initiated by the TSEI register bit.
When 1, error insertion is initiated by the transmit manual error insertion signal (TMEI). Note: If TMEI or TSEI is
one, changing the state of this bit may cause an error to be inserted.
00 = F-bit error.
01 = M-bit error.
10 = SEF error.
11 = OOMF error.
Reserved
15
—
0
7
0
CPEIE
14
—
0
6
0
T3.TEIR
T3 Transmit Error Insertion Register
(1,3,5,7)1Ah
PEI
13
—
0
5
0
FEIC1
12
—
0
0
4
278
CCPEIE
FEIC0
11
0
3
0
CPEI
FEI
10
0
2
0
CFBEIE
TSEI
9
0
1
0
MEIMS
FBEI
8
0
0
0