DF70844AD80FPV Renesas Electronics America, DF70844AD80FPV Datasheet - Page 904

• Manufacturer Part Number: DF70844AD80FPV
• Description: IC SUPERH MCU FLASH 112LQFP
• Manufacturer: Renesas Electronics America
• Series: SuperH® SH7080r

Specifications of DF70844AD80FPV

• Core Size: 32-Bit
• Program Memory Size: 256KB (256K x 8)
• Core Processor: SH-2
• Speed: 80MHz
• Connectivity: EBI/EMI, FIFO, I²C, SCI, SSU
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 76
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• No. Of I/o's: 76
• Ram Memory Size: 16KB
• Cpu Speed: 80MHz
• Digital Ic Case Style: LQFP
• Supply Voltage Range: 3V To 3.6V, 4.5V To 5.5V
• Embedded Interface Type: I2C, SCI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: R0K570865S001BE - KIT STARTER FOR SH7086R0K570865S000BE - KIT STARTER FOR SH7086HS0005KCU11H - EMULATOR E10A-USB H8S(X),SH2(A)
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Section 16 Serial Communication Interface with FIFO (SCIF)
In transmitting serial data, the SCIF operates as follows:
1. When data is written into the transmit FIFO data register (SCFTDR), the SCIF transfers the
2. When data is transferred from SCFTDR to SCTSR and transmission is started, consecutive
3. The SCIF checks the SCFTDR transmit data at the timing for sending the MSB (bit 7). If data
4. After the end of serial transmission, the SCK pin is held in the high state.
Figure 16.14 shows an example of SCIF transmit operation.
Rev. 3.00 May 17, 2007 Page 846 of 1582
REJ09B0181-0300
data from SCFTDR to the transmit shift register (SCTSR) and starts transmitting. Confirm that
the TDFE flag in the serial status register (SCFSR) is set to 1 before writing transmit data to
SCFTDR. The number of data bytes that can be written is (16 – transmit trigger setting).
transmit operations are performed until there is no transmit data left in SCFTDR. When the
number of transmit data bytes in SCFTDR falls below the transmit trigger number set in the
FIFO control register (SCFCR), the TDFE flag is set. If the TIE bit in the serial control register
(SCSR) is set to 1 at this time, a transmit-FIFO-data-empty interrupt (TXIF) request is
generated.
If clock output mode is selected, the SCIF outputs eight synchronous clock pulses. If an
external clock source is selected, the SCIF outputs data in synchronization with the input
clock. Data is output from the TXD pin in order from the LSB (bit 0) to the MSB (bit 7).
is present, the data is transferred from SCFTDR to SCTSR, the MSB (bit 7) is sent, and then
serial transmission of the next frame is started. If there is no transmit data, the TEND flag in
SCFSR is set to 1, the MSB (bit 7) is sent, and then the TXD pin holds the states.
Synchronization
Serial data
TEND
TDFE
clock
interrupt
request
Figure 16.14 Example of SCIF Transmit Operation
TXIF
Data written to SCFTDR
Bit 0
LSB
and TDFE flag cleared
to 0 by TXIF interrupt
handler
Bit 1
One frame
interrupt
request
TXIF
MSB
Bit 7
Bit 0
Bit 1
Bit 6
Bit 7