C8051F120-GQR Silicon Laboratories Inc, C8051F120-GQR Datasheet - Page 296

• Manufacturer Part Number: C8051F120-GQR
• Description: IC 8051 MCU FLASH 128K 100TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F12xr

Specifications of C8051F120-GQR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 100MHz
• Connectivity: EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 64
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8.25K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x8b, 8x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• Processor Series: C8051F1x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 8.25 KB
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Clock Frequency: 100 MHz
• Number Of Programmable I/os: 64
• Number Of Timers: 5
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F120DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 8 Channel
• On-chip Dac: 12 bit, 2 Channel
• For Use With: 336-1285 - KIT DEV EMBEDDED MODEM336-1284 - KIT DEV EMBEDDED ETHERNET336-1224 - DEVKIT-F120/21/22/23/24/25/26/27
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

C8051F120/1/2/3/4/5/6/7
C8051F130/1/2/3
296
Bits7–6: SM00–SM10: Serial Port Operation Mode:
Bit5:
Bit4:
Bit3:
Bit2:
Bit1:
Bit0:
SM00
R/W
Bit7
Write:
When written, these bits select the Serial Port Operation Mode as follows:
Reading these bits returns the current UART0 mode as defined above.
SM20: Multiprocessor Communication Enable.
The function of this bit is dependent on the Serial Port Operation Mode.
Mode 0: No effect
Mode 1: Checks for valid stop bit.
Mode 2 and 3: Multiprocessor Communications Enable.
received address matches the UART0 address or the broadcast address.
REN0: Receive Enable.
This bit enables/disables the UART0 receiver.
0: UART0 reception disabled.
1: UART0 reception enabled.
TB80: Ninth Transmission Bit.
The logic level of this bit will be assigned to the ninth transmission bit in Modes 2 and 3. It is
not used in Modes 0 and 1. Set or cleared by software as required.
RB80: Ninth Receive Bit.
The bit is assigned the logic level of the ninth bit received in Modes 2 and 3. In Mode 1, if
SM20 is logic 0, RB80 is assigned the logic level of the received stop bit. RB8 is not used in
Mode 0.
TI0: Transmit Interrupt Flag.
Set by hardware when a byte of data has been transmitted by UART0 (after the 8th bit in
Mode 0, or at the beginning of the stop bit in other modes). When the UART0 interrupt is
enabled, setting this bit causes the CPU to vector to the UART0 interrupt service routine.
This bit must be cleared manually by software
RI0: Receive Interrupt Flag.
Set by hardware when a byte of data has been received by UART0 (as selected by the
SM20 bit). When the UART0 interrupt is enabled, setting this bit causes the CPU to vector
to the UART0 interrupt service routine. This bit must be cleared manually by software.
SM00
0
0
1
1
SM10
R/W
Bit6
0: Logic level of stop bit is ignored.
1: RI0 will only be activated if stop bit is logic level 1.
0: Logic level of ninth bit is ignored.
1: RI0 is set and an interrupt is generated only when the ninth bit is logic 1 and the
SFR Definition 21.1. SCON0: UART0 Control
SM10
0
1
0
1
SM20
R/W
Bit5
Mode 1: 8-Bit UART, Variable Baud Rate
Mode 3: 9-Bit UART, Variable Baud Rate
Mode 2: 9-Bit UART, Fixed Baud Rate
REN0
R/W
Bit4
Mode 0: Synchronous Mode
Rev. 1.4
TB80
R/W
Bit3
Mode
RB80
R/W
Bit2
R/W
TI0
Bit1
SFR Address:
SFR Page:
R/W
RI0
Bit0
0x98
0
00000000
Addressable
Reset Value
Bit